9 open source boards using the TPS61023
Real designs built with the TPS61023, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
MistMaker-Battery-Kit
Dav1dyang
38 × 25.1 mm54 parts2LMIT26Raspberry Pi
KRUPS Flight Computer
krups
127 × 64.4 mm108 parts6LNo license0ESP32
RC vel car
surya-shreevathsa11
46 × 32 mm70 parts4LNo license0LaserController
GrussmayerLab
100 × 80 mm44 parts2LNo license0ESP32
Kira
Przz23
110 × 75 mm22 parts2LNo license0- schematic only · 65 parts
LazerGamebox
7kasper
65 partsNo license0 Mist Maker
Dav1dyang
50.8 × 26.7 mm37 parts2LMIT26Raspberry Pi
KRUPS-RocketStation
krups
87.6 × 56 mm34 parts4LNo license0Raspberry Pi
KRUPS-FemtoSat
krups
29.2 × 71.9 mm32 parts4LNo license0
How designs wire the TPS61023
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the TPS61023 connects to, and the resistors, capacitors and other passives placed on it.
- The FB_1 pin has a pull-up to 5V on 4 of 5 designs, most often 732 kΩ (then 820 kΩ).
- The SW_5 pin has a inductor on 4 of 5 designs, most often 1 µH.
- The FB_1 pin has a resistor to GND on 3 of 5 designs, most often 100 kΩ.
- The EN_2 pin has a series resistor on 2 of 5 designs, most often 10 kΩ (then 1.5 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| FB_1pin 1 | Connected to: Signal 80% · VIN_PRE 20% |
|
| EN_2pin 2 | Connected to: Signal 80% · 3.3V 20% |
|
| VIN_3pin 3 | Connected to: 3.3V 60% · not connected 20% · a signal 20% |
|
| GND_4pin 4 | Connected to: GND 60% · VIN 20% · a signal 20% | — |
| SW_5pin 5 | Connected to: Signal 80% · not connected 20% |
|
| VOUT_6pin 6 | Connected to: 5V 100% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include MistMaker-Battery-Kit by Dav1dyang, LaserController by GrussmayerLab, KRUPS Flight Computer by krups and Kira by Przz23.
The TPS61023 in open source designs
The gallery holds 9 open source boards using the TPS61023 from 6 GitHub repositories; a typical one measures about 69.2 × 60.2 mm and carries around 44 components.
50% are two-layer designs, the rest use four layers or more, and 22% carry an open source license.
The most starred is MistMaker-Battery-Kit by Dav1dyang.
Parts used alongside the TPS61023
Microcontrollers on boards using the TPS61023
What boards using the TPS61023 are built for
TPS61023: common questions
Where can I find a TPS61023 reference design?
Each of the 9 boards on this page is a real design using the TPS61023. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the TPS61023 FB_1 pin?
The FB_1 pin has a pull-up to 5V on 4 of 5 designs, most often 732 kΩ (then 820 kΩ). Counted from the KiCad layouts of 5 open source designs using the TPS61023.
How is the TPS61023 SW_5 pin connected?
The SW_5 pin has a inductor on 4 of 5 designs, most often 1 µH. Counted from the KiCad layouts of 5 open source designs using the TPS61023.
What resistor goes on the TPS61023 EN_2 pin?
The EN_2 pin has a series resistor on 2 of 5 designs, most often 10 kΩ (then 1.5 kΩ). Counted from the KiCad layouts of 5 open source designs using the TPS61023.
Which microcontrollers do boards using the TPS61023 use?
Most are built on Raspberry Pi (3) and ESP32 (2).
How big is a typical board using the TPS61023?
The median is 69.2 × 60.2 mm, and 50% are two-layer designs.
What is the most popular open source board using the TPS61023?
By GitHub stars, MistMaker-Battery-Kit by Dav1dyang, with 26 stars.
Can I simulate one of these boards using the TPS61023 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.