15 open source boards using the UMH3N
Real designs built with the UMH3N, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
FujiNet-Astrocade-Rev0
FujiNetWIFI
96 × 58 mm77 parts6LCERN-OHL-S-2.0138- schematic only · 56 partsESP32
KiCad-PCB-design workshop
LEDs-by-glowingkitty
56 partsGPL-3.09 ESP32
ESP32-S3 Dev Board
hw-tinkerers
123.5 × 56.5 mm146 parts4LNo license0ESP32
Lacarriere station
pier-cbd
92 × 92 mm78 parts2LNo license0ESP32
FujiNet-INTV-Rev0
FujiNetWIFI
58.2 × 78 mm77 parts4LCERN-OHL-S-2.0138GlowBand Dock
LEDs-by-glowingkitty
26.8 × 15.4 mm13 parts2LMIT4ESP32
R2 HH Controllers
greghulette
56.6 × 111 mm122 parts4LNo license2ESP32
Body Controller V1
greghulette
123 × 78 mm94 parts4LNo license2ESP32
Body LED Controller V1
greghulette
123 × 78 mm94 parts4LNo license2ESP32
Servo Controller 2 PCA9685
greghulette
114.1 × 70.3 mm35 parts4LNo license2ESP32
Dome Controller
greghulette
136.5 × 70 mm33 parts4LNo license2ESP32
UI V1 WROOM
Gamu2124
80 × 49 mm51 parts2LNo license1ESP32
Dome Plate Controller V1
greghulette
118 × 78.6 mm33 parts4LNo license2ESP32
Body Servos
greghulette
80 × 55.2 mm30 parts4LNo license2ESP32
Dome Logics V1
greghulette
54.9 × 51.9 mm26 parts4LNo license2
How designs wire the UMH3N
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the UMH3N connects to, and the resistors, capacitors and other passives placed on it.
- The C pins have a capacitor to GND on 5 of 6 designs, most often 100 nF (then 1 µF).
- The C pins have a pull-up to 3.3V on 5 of 6 designs, most often 10 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Cpin 3, 6 | Connected to: The microcontroller 83%, a connector 25% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include FujiNet-Astrocade-Rev0 by FujiNetWIFI, GlowBand Dock PCB by LEDs-by-glowingkitty, Body Controller V1 by greghulette and UI V1 WROOM by Gamu2124.
The UMH3N in open source designs
The gallery holds 15 open source boards using the UMH3N from 7 GitHub repositories; a typical one measures about 94 × 70.1 mm and carries around 56 components.
79% use four copper layers or more, and 27% carry an open source license.
The most starred is FujiNet-Astrocade-Rev0 by FujiNetWIFI.
Parts used alongside the UMH3N
Microcontrollers on boards using the UMH3N
What boards using the UMH3N are built for
UMH3N: common questions
Where can I find a UMH3N reference design?
Each of the 15 boards on this page is a real design using the UMH3N. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the UMH3N C pin connected?
The C pins have a capacitor to GND on 5 of 6 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 6 open source designs using the UMH3N.
What parts are used alongside the UMH3N?
The CH340C, CP2102-GMR and USBLC6-2SC6 appear in the most repositories here.
Which microcontrollers do boards using the UMH3N use?
Most are built on ESP32 (14).
How big is a typical board using the UMH3N?
The median is 94 × 70.1 mm, and 21% are two-layer designs.
What is the most popular open source board using the UMH3N?
By GitHub stars, FujiNet-Astrocade-Rev0 by FujiNetWIFI, with 138 stars.
Can I simulate one of these boards using the UMH3N before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.