13 open source boards using the >VALUE

Real designs built with the >VALUE, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

13 boardsClear filters|Most starred

How designs wire the >VALUE

Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the >VALUE connects to, and the resistors, capacitors and other passives placed on it.

  • The NIRQ pin has a series resistor on 6 of 8 designs, most often 8.25 MΩ (then 374 kΩ).
  • The BT_ON pin is tied to VBAT_OK on 5 of 8 designs (a signal on 3).
  • The GND pins have a capacitor to GND on 4 of 8 designs, most often 10 nF.
  • The GND pins have a series resistor on 4 of 8 designs, most often 7.32 MΩ (then 8.25 MΩ).
GNDpin 1, 4, 7, 11, 15, 21Connected to: GND 56% · a signal 37%
  • Capacitor to GND on 50% · 10 nF (4)
  • Series resistor on 50% · 7.32 MΩ (4), 8.25 MΩ (4)
  • Resistor to GND on 50% · 5.62 MΩ (4), 4.53 MΩ (4)
NCpin 2, 19, 20Connected to: Signal 65% · not connected 31%
  • Capacitor to GND on 50% · 4.7 µF (8), 100 nF (7), 100 µF (4)
  • Series resistor on 50% · 0 Ω (8)
  • Inductor on 50% · 22 µH (8)
SCLKpin 3Connected to: Signal 88%
  • Series resistor on 50% · 0 Ω (8)
  • Resistor to GND on 50% · 0 Ω (4)
DOpin 6Connected to: Signal 88%
  • Pull-up to VBAT_OK on 50% · 0 Ω (4)
  • Capacitor to GND on 50% · 1 µF (4)
GPIO0pin 8Connected to: Signal 63% · not connected 38%
  • Series resistor on 50% · 374 kΩ (4), 8.25 MΩ (4), 7.32 MΩ (4)
NIRQpin 10Connected to: Signal 88%
  • Series resistor on 75% · 8.25 MΩ (4), 374 kΩ (4), 10 kΩ (2)
WL_ONpin 12Connected to: A connector 25%
  • Resistor to GND on 50% · 4.75 MΩ (4)
  • Series resistor on 50% · 8.25 MΩ (4)
BT_ONpin 13Connected to: VBAT_OK 63% · a signal 38%
VDDIOpin 14Connected to: Signal 63% · 3.3V 38%
  • Capacitor to GND on 50% · 22 µF (4), 100 nF (3), 100 µF (3)
  • Inductor on 50% · 10 µH (4)
VINpin 16Connected to: Signal 63% · 3.3V 38%
  • Inductor on 50% · 10 µH (4)

4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include SolarCellX v3 by spacecraft-design-lab-2019, Spark-2350 by PythonAtSea, L by Hasatio and CaravelPmod by mdrobot7.

The >VALUE in open source designs

The gallery holds 13 open source boards using the >VALUE from 9 GitHub repositories; a typical one measures about 48.4 × 50 mm and carries around 58 components.

54% use four copper layers or more, and 15% carry an open source license.

The most starred is SolarCellX v3 by spacecraft-design-lab-2019.

Parts used alongside the >VALUE

Microcontrollers on boards using the >VALUE

What boards using the >VALUE are built for

>VALUE: common questions

Where can I find a >VALUE reference design?

Each of the 13 boards on this page is a real design using the >VALUE. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What resistor goes on the >VALUE NIRQ pin?

The NIRQ pin has a series resistor on 6 of 8 designs, most often 8.25 MΩ (then 374 kΩ). Counted from the KiCad layouts of 8 open source designs using the >VALUE.

How is the >VALUE BT_ON pin connected?

The BT_ON pin is tied to VBAT_OK on 5 of 8 designs (a signal on 3). Counted from the KiCad layouts of 8 open source designs using the >VALUE.

How is the >VALUE GND pin connected?

The GND pins have a capacitor to GND on 4 of 8 designs, most often 10 nF. Counted from the KiCad layouts of 8 open source designs using the >VALUE.

What parts are used alongside the >VALUE?

The TSL2561, RP2350_80QFN and SW_SPDT appear in the most repositories here.

Which microcontrollers do boards using the >VALUE use?

Most are built on ESP32 (4) and RP2040/RP2350 (4).

How big is a typical board using the >VALUE?

The median is 48.4 × 50 mm, and 46% are two-layer designs.

What is the most popular open source board using the >VALUE?

By GitHub stars, SolarCellX v3 by spacecraft-design-lab-2019, with 12 stars.

Can I simulate one of these boards using the >VALUE before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part