16 open source boards using the 24LC02

Real designs built with the 24LC02, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

16 boardsClear filters|Most starred

How designs wire the 24LC02

Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the 24LC02 connects to, and the resistors, capacitors and other passives placed on it.

  • The A1 pin is tied to GND on 6 of 9 designs (a signal on 2).
  • The A2 pin is tied to GND on 6 of 9 designs (a signal on 3).
  • The SDA pin has a pull-up to 3.3V on 4 of 9 designs, most often 10 kΩ (then 4.7 kΩ).
  • The WP pin has a pull-up to 5V on 4 of 9 designs, most often 10 kΩ (then 100 kΩ).
A1pin 2Connected to: GND 67% · a signal 22%
A2pin 3Connected to: GND 67% · a signal 33%
GNDpin 4Connected to: GND 89%
SDApin 5Connected to: A connector 56%, PCA9555 22%
  • Pull-up to 3.3V on 44% · 10 kΩ (2), 4.7 kΩ (1)
SCLpin 6Connected to: A connector 56%, PCA9555 22%
  • Pull-up to 3.3V on 33% · 10 kΩ (2), 4.7 kΩ (1)
WPpin 7Connected to: PCA9555 22% · GND 33%
  • Pull-up to 5V on 44% · 10 kΩ (3), 100 kΩ (1)
VCCpin 8Connected to: 3.3V 89%
  • Decoupling capacitor on 33% · 1 µF (2), 100 nF (2)

1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include 6xUSB PowMet by aleksejm, DomoNode-InOut by NdK73, Hdmi2rgb adapter by embeddedboys and Midi controller by Tommie1236.

The 24LC02 in open source designs

The gallery holds 16 open source boards using the 24LC02 from 9 GitHub repositories; a typical one measures about 95 × 74.5 mm and carries around 51 components.

75% are two-layer designs, the rest use four layers or more, and 50% carry an open source license.

The most starred is 6xUSB PowMet by aleksejm.

Parts used alongside the 24LC02

Microcontrollers on boards using the 24LC02

24LC02: common questions

Where can I find a 24LC02 reference design?

Each of the 16 boards on this page is a real design using the 24LC02. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the 24LC02 A1 pin connected?

The A1 pin is tied to GND on 6 of 9 designs (a signal on 2). Counted from the KiCad layouts of 9 open source designs using the 24LC02.

How is the 24LC02 A2 pin connected?

The A2 pin is tied to GND on 6 of 9 designs (a signal on 3). Counted from the KiCad layouts of 9 open source designs using the 24LC02.

What pull-up resistor is used on the 24LC02 SDA pin?

The SDA pin has a pull-up to 3.3V on 4 of 9 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 9 open source designs using the 24LC02.

What parts are used alongside the 24LC02?

The ESP-12, HLK-PM01, PCA9555 and TLP620 appear in the most repositories here.

Which microcontrollers do boards using the 24LC02 use?

Most are built on ESP8266 (3), STM32 (2) and RP2040/RP2350 (1).

How big is a typical board using the 24LC02?

The median is 95 × 74.5 mm, and 75% are two-layer designs.

What is the most popular open source board using the 24LC02?

By GitHub stars, 6xUSB PowMet by aleksejm, with 7 stars.

Can I simulate one of these boards using the 24LC02 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part