15 open source boards using the HLK-PM01
Real designs built with the HLK-PM01, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP8266
Domonode2
NdK73
95 × 139.6 mm103 parts2LMIT5STM32
PCB Real-Time-Power-Monitoring-System-Development sensor
NguyenThanhHuy-debug
101.6 × 50.8 mm122 parts2LNo license2ESP32
Home-Automation by using esp32 WROOM32D-pcb-
Noraiz963
88.3 × 68.8 mm28 parts2LNo license2ESP32
Sprinkler-System
Swamp-Ig
165 × 85 mm73 parts2LNo license0AVR/Arduino
LORA remote relays
motivemachine
85.1 × 99.8 mm38 parts2LApache-2.00RP2040/RP2350
Pico energymeter
jabezmcc
115 × 108 mm27 parts2LGPL-3.00ESP32-Smart-Energy-Meter
debugAyo
121.9 × 99.1 mm11 parts2LNo license0ESP8266
Domonode
chipsi007
47 parts2LMIT0ESP8266
Domonode
NdK73
47 parts2LMIT5DomoNode-InOut
chipsi007
95 × 80 mm47 parts2LMIT0DomoNode-InOut
NdK73
95 × 80 mm47 parts2LMIT5AVR/Arduino
MySensors 2Relais
LudovicLemarinel
56 × 57 mm17 parts2LNo license4AVR/Arduino
MySensors FilPilote nrf24
LudovicLemarinel
50 × 50 mm15 parts2LNo license4AVR/Arduino
MySensors 1Relay
LudovicLemarinel
42.5 × 50 mm14 parts2LNo license4AVR/Arduino
MySensors FilPilote RFM69
LudovicLemarinel
47.5 × 49 mm14 parts2LNo license4
How designs wire the HLK-PM01
Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the HLK-PM01 connects to, and the resistors, capacitors and other passives placed on it.
- The -VOUT_3 pin is tied to GND on 7 of 9 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| -VOUT_3pin 3 | Connected to: GND 78% | — |
| +VOUT_4pin 4 | Connected to: 5V 67% · a signal 22% | — |
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Domonode by NdK73, MySensors 1Relay by LudovicLemarinel, PCB Real-Time-Power-Monitoring-System-Development sensor by NguyenThanhHuy-debug and Home-Automation by using esp32 WROOM32D-pcb- by Noraiz963.
The HLK-PM01 in open source designs
The gallery holds 15 open source boards using the HLK-PM01 from 9 GitHub repositories; a typical one measures about 95 × 80 mm and carries around 38 components.
100% are two-layer designs, the rest use four layers or more, and 47% carry an open source license.
The most starred is Domonode2 by NdK73.
Parts used alongside the HLK-PM01
Microcontrollers on boards using the HLK-PM01
What boards using the HLK-PM01 are built for
HLK-PM01: common questions
Where can I find a HLK-PM01 reference design?
Each of the 15 boards on this page is a real design using the HLK-PM01. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the HLK-PM01 -VOUT_3 pin connected?
The -VOUT_3 pin is tied to GND on 7 of 9 designs. Counted from the KiCad layouts of 9 open source designs using the HLK-PM01.
What parts are used alongside the HLK-PM01?
The AMS1117-3.3, 24LC02, ESP-12, PCA9555 and TLP620 appear in the most repositories here.
Which microcontrollers do boards using the HLK-PM01 use?
Most are built on AVR/Arduino (5), ESP8266 (3), ESP32 (2) and RP2040/RP2350 (1).
How big is a typical board using the HLK-PM01?
The median is 95 × 80 mm, and 100% are two-layer designs.
What is the most popular open source board using the HLK-PM01?
By GitHub stars, Domonode2 by NdK73, with 5 stars.
Can I simulate one of these boards using the HLK-PM01 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.