16 open source boards using the 5V
Real designs built with the 5V, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
RP2040/RP2350
HydraMeter 0.4
jduffy105
76.2 × 114.3 mm288 parts2LCERN-OHL-S-2.0174Avr door controller
AlbanBedel
121 × 70 mm67 parts2LNo license10ESP32
GyroCube
Pedro-51
73.5 × 52.1 mm23 parts2LNo license7- schematic only · 69 partsAVR/Arduino
Thotcon0x5
Workshop88
69 partsNo license7 Main Board
callmestiles
137.2 × 151.2 mm86 parts2LNo license2AVR/Arduino
Grinder timer
Clewsy
75 × 120 mm31 parts2LMIT1Hw micropow
aw
44 × 22 mm12 parts2LCC-BY-SA-4.01ESP32
MiAM PAMI V3 Stepper
14chanwa
62 × 95 mm33 parts2LNo license0AVR/Arduino
Indicator board 3V3 & 5V
callmestiles
100 × 73.3 mm83 parts2LNo license2ESP32
MiAM PAMI 2024 DC
14chanwa
69.8 × 96.8 mm31 parts2LNo license0ESP32
BoneIO - dimmer board 4x4A
boneIO-eu
67.8 × 86.9 mm106 parts2LGPL-3.02RP2040/RP2350
Output controller
mekatrol
238 × 122 mm161 parts2LNo license0BoneIO - expansion module
boneIO-eu
86 × 74 mm74 parts2LGPL-3.02RP2040/RP2350
Controller
mekatrol
140 × 100 mm146 parts2LNo license0Powercircuitabu2023
ArunCH404
137 × 65.8 mm21 parts2LNo license0ESP32
MiAM PAMI V3 DC
14chanwa
62 × 95 mm26 parts2LNo license0
How designs wire the 5V
Read from the KiCad layouts of 10 open source designs, one per repository: what each pin of the 5V connects to, and the resistors, capacitors and other passives placed on it.
- The VOUT pin is tied to GND on 3 of 4 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VINpin 1 | Connected to: 12V 70% · GND 20% |
|
| VOUTpin 5 | Connected to: GND 75% · VSYS 25% | — |
3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include HydraMeter 0.4 by jduffy105, Avr door controller by AlbanBedel, GyroCube by Pedro-51 and BoneIO - dimmer board 4x4A by boneIO-eu.
The 5V in open source designs
The gallery holds 16 open source boards using the 5V from 11 GitHub repositories; a typical one measures about 76.2 × 95 mm and carries around 68 components.
100% are two-layer designs, the rest use four layers or more, and 31% carry an open source license.
The most starred is HydraMeter 0.4 by jduffy105.
Microcontrollers on boards using the 5V
What boards using the 5V are built for
5V: common questions
Where can I find a 5V reference design?
Each of the 16 boards on this page is a real design using the 5V. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the 5V VOUT pin connected?
The VOUT pin is tied to GND on 3 of 4 designs. Counted from the KiCad layouts of 10 open source designs using the 5V.
Which microcontrollers do boards using the 5V use?
Most are built on ESP32 (5), AVR/Arduino (3) and RP2040/RP2350 (3).
How big is a typical board using the 5V?
The median is 76.2 × 95 mm, and 100% are two-layer designs.
What is the most popular open source board using the 5V?
By GitHub stars, HydraMeter 0.4 by jduffy105, with 174 stars.
Can I simulate one of these boards using the 5V before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.