10 open source boards using the 74HC132
Real designs built with the 74HC132, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
8 16 computer 2
halfburnttoast
208 × 110 mm111 parts2LNo license21AVR/Arduino
Hauptplatine
JoshCrouch
220 × 160.5 mm504 parts4LNo license0Towns power supply adapter
neko32k
48 × 51 mm20 parts2LMIT0Motherboard
AndersBNielsen
144.8 × 94 mm37 parts2LNo license4Full
durangoretro
177.8 × 130.8 mm121 parts2LNo license08 16 computer 2 serial card
halfburnttoast
48 × 94 mm14 parts2LNo license21Spi
durangoretro
82.6 × 39.4 mm29 parts2LNo license0Rtc sd
zuiko21
53.3 × 130.8 mm34 parts2LMIT23Chihuahua
zuiko21
97.8 × 72.4 mm33 parts2LMIT23Spi
zuiko21
82.6 × 39.4 mm29 parts2LMIT23
How designs wire the 74HC132
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the 74HC132 connects to, and the resistors, capacitors and other passives placed on it.
- Pin 3 has a series resistor on 3 of 6 designs, most often 4.7 kΩ (then 1 kΩ).
- The VCC_14 pin has a decoupling capacitor on 3 of 6 designs, most often 100 nF (then 1 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 2 | Connected to: Signal 100% |
|
| Pin 3 | Connected to: A connector 33% · not connected 33% |
|
| GND_7pin 7 | Connected to: GND 100% | — |
| Pin 10 | Connected to: Signal 83% · 5V 17% |
|
| VCC_14pin 14 | Connected to: 5V 100% |
|
9 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Chihuahua by zuiko21, 8 16 computer 2 by halfburnttoast, Motherboard by AndersBNielsen and Full by durangoretro.
The 74HC132 in open source designs
The gallery holds 10 open source boards using the 74HC132 from 6 GitHub repositories; a typical one measures about 90.2 × 94 mm and carries around 34 components.
90% are two-layer designs, the rest use four layers or more, and 40% carry an open source license.
The most starred is Rtc sd by zuiko21.
Parts used alongside the 74HC132
Microcontrollers on boards using the 74HC132
What boards using the 74HC132 are built for
74HC132: common questions
Where can I find a 74HC132 reference design?
Each of the 10 boards on this page is a real design using the 74HC132. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the 74HC132 pin 3?
Pin 3 has a series resistor on 3 of 6 designs, most often 4.7 kΩ (then 1 kΩ). Counted from the KiCad layouts of 6 open source designs using the 74HC132.
What decoupling capacitors do designs use on the 74HC132 VCC_14 pin?
The VCC_14 pin has a decoupling capacitor on 3 of 6 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 6 open source designs using the 74HC132.
What parts are used alongside the 74HC132?
The 74HC245, 74HC138, 74HC74, 62256 and 65C02 appear in the most repositories here.
Which microcontrollers do boards using the 74HC132 use?
Most are built on AVR/Arduino (1).
How big is a typical board using the 74HC132?
The median is 90.2 × 94 mm, and 90% are two-layer designs.
What is the most popular open source board using the 74HC132?
By GitHub stars, Rtc sd by zuiko21, with 23 stars.
Can I simulate one of these boards using the 74HC132 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.