8 open source boards using the 74LS01
Real designs built with the 74LS01, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
RC1 UI
tebl
99.1 × 97.2 mm89 parts2LCERN-OHL-1.225Junior interface
laurent-fr
217.2 × 113 mm116 parts2LCC-BY-NC-4.014JC2 v4.1
Emile666
233.7 × 160 mm120 parts2LNo license3AVR/Arduino
AbuDhabi ElectronBeam
monicaespinosa
130 × 145 mm53 parts2LNo license1Junior universal memory
laurent-fr
160 × 100 mm38 parts2LCC-BY-NC-4.014256 word memory
ibm2030
220 × 160 mm36 parts2LNo license13Program counter and adder logic
ibm2030
220 × 160 mm29 parts2LNo license13PC and ADDER 74LS74 MOD
ibm2030
220 × 160 mm28 parts2LNo license13
How designs wire the 74LS01
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the 74LS01 connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 3 of 5 designs, most often 100 nF.
- Pin 1 has a pull-up to VCC on 2 of 5 designs, most often 10 kΩ (then 470 Ω).
- Pin 4 has a pull-up to VCC on 2 of 5 designs, most often 1 kΩ (then 4.7 kΩ).
- Pin 10 has a pull-up to VCC on 2 of 5 designs, most often 1 kΩ (then 4.7 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: A connector 60% |
|
| Pin 4 | Connected to: A connector 40% · not connected 20% |
|
| GNDpin 7 | Connected to: GND 100% | — |
| Pin 10 | Connected to: A connector 40% · not connected 20% · GND 20% |
|
| Pin 13 | Connected to: Signal 60% · not connected 20% · GND 20% |
|
| VCCpin 14 | Connected to: 5V 80% · a signal 20% |
|
8 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include RC1 UI by tebl, Junior interface by laurent-fr, 256 word memory by ibm2030 and JC2 v4.1 by Emile666.
The 74LS01 in open source designs
The gallery holds 8 open source boards using the 74LS01 from 5 GitHub repositories; a typical one measures about 218.6 × 152.5 mm and carries around 46 components.
100% are two-layer designs, the rest use four layers or more, and 13% carry an open source license.
The most starred is RC1 UI by tebl.
Microcontrollers on boards using the 74LS01
What boards using the 74LS01 are built for
74LS01: common questions
Where can I find a 74LS01 reference design?
Each of the 8 boards on this page is a real design using the 74LS01. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the 74LS01 VCC pin?
The VCC pin has a decoupling capacitor on 3 of 5 designs, most often 100 nF. Counted from the KiCad layouts of 5 open source designs using the 74LS01.
What pull-up resistor is used on the 74LS01 pin 1?
Pin 1 has a pull-up to VCC on 2 of 5 designs, most often 10 kΩ (then 470 Ω). Counted from the KiCad layouts of 5 open source designs using the 74LS01.
What pull-up resistor is used on the 74LS01 pin 4?
Pin 4 has a pull-up to VCC on 2 of 5 designs, most often 1 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 5 open source designs using the 74LS01.
What parts are used alongside the 74LS01?
The 74LS00, 6522, 74LS04 and 74LS20 appear in the most repositories here.
Which microcontrollers do boards using the 74LS01 use?
Most are built on AVR/Arduino (1).
How big is a typical board using the 74LS01?
The median is 218.6 × 152.5 mm, and 100% are two-layer designs.
What is the most popular open source board using the 74LS01?
By GitHub stars, RC1 UI by tebl, with 25 stars.
Can I simulate one of these boards using the 74LS01 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.