11 open source boards using the AD620
Real designs built with the AD620, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Amplifier
MarinosK
99.1 × 99.1 mm69 parts2LNo license4MadEEG
timkoval
81.5 × 63.9 mm98 parts2LMIT2Standalone pi loop
matterwaves
100 × 100 mm36 parts4LNo license2AVR/Arduino
Diy ert
CainPatel
127 × 117.5 mm44 parts2LMIT1EEG Prototype
diosey
81.6 × 96.4 mm55 parts2LGPL-3.00Emg smd
intropercib
45.4 × 38 mm38 parts2LMIT0Esp32-thermocouple
jackestar
37.3 × 52.5 mm10 parts2LMIT0Amplifier.kicad pcb-CNC version (with some problems)
MarinosK
99.1 × 99.1 mm67 parts2LNo license4Emg tht
intropercib
56 × 45.6 mm38 parts2LMIT0Earthboot
microresearch
49.7 × 130.1 mm44 parts2LGPL-3.05Earthboot withnewsoldermask
microresearch
49.7 × 130.1 mm42 parts2LGPL-3.05
How designs wire the AD620
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the AD620 connects to, and the resistors, capacitors and other passives placed on it.
- The RG pins have a series resistor on 7 of 8 designs, most often 1 kΩ (then 220 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| RGpin 1, 8 | Connected to: Signal 100% |
|
| -pin 2 | Connected to: A connector 38% |
|
| +pin 3 | Connected to: A connector 38% |
|
| VS-pin 4 | Connected to: GND 50% · -9V 38% |
|
| Pin 6 | Connected to: A connector 38% |
|
| VS+pin 7 | Connected to: 5V 88% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Earthboot by microresearch, Amplifier by MarinosK, Standalone pi loop by matterwaves and MadEEG by timkoval.
The AD620 in open source designs
The gallery holds 11 open source boards using the AD620 from 8 GitHub repositories; a typical one measures about 81.5 × 99.1 mm and carries around 44 components.
91% are two-layer designs, the rest use four layers or more, and 73% carry an open source license.
The most starred is Earthboot by microresearch.
Parts used alongside the AD620
Microcontrollers on boards using the AD620
What boards using the AD620 are built for
AD620: common questions
Where can I find a AD620 reference design?
Each of the 11 boards on this page is a real design using the AD620. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the AD620 RG pin?
The RG pins have a series resistor on 7 of 8 designs, most often 1 kΩ (then 220 Ω). Counted from the KiCad layouts of 8 open source designs using the AD620.
What parts are used alongside the AD620?
The ADS1115IDGS, LM324 and LM358 appear in the most repositories here.
Which microcontrollers do boards using the AD620 use?
Most are built on AVR/Arduino (1).
How big is a typical board using the AD620?
The median is 81.5 × 99.1 mm, and 91% are two-layer designs.
What is the most popular open source board using the AD620?
By GitHub stars, Earthboot by microresearch, with 5 stars.
Can I simulate one of these boards using the AD620 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.