172 open source boards using the LM324
Real designs built with the LM324, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kSnark barker
schlae
231.1 × 106.7 mm193 parts2LNo license687ZC95 MKII
CrashOverride85
191.5 × 76 mm319 parts2LGPL-3.0115SNSP-CPU-01
stonedDiscord
215.8 × 159 mm276 parts2LGPL-3.065AVR/Arduino
OtterX
RetroRemake
170.1 × 170.1 mm168 parts4LCERN-OHL-W-2.040Voice board
Windfisch
83.8 × 72.4 mm127 parts2LGPL-3.031PIC
Usb morse keyer
dilshan
169.4 × 48.8 mm79 parts2LMIT17Synbal
Bad-Dog-Designs
71 × 108 mm105 parts2LGPL-2.014MICRO-OX Main VCO board
JordanAceto
133.9 × 165.1 mm280 parts4LCC-BY-4.08SoundX
SukkoPera
60.8 × 100 mm44 parts2LNo license8AVR/Arduino
Muscle imbalance detection
leikoilja
56.8 × 68.6 mm82 parts2LMIT6RP2040/RP2350
Robocat
Windfisch
90 × 70 mm79 parts2LNo license6ESP32-Sentinel-Kinetic-Wireless-Dongle
alextrical
50 × 50 mm70 parts4LCERN-OHL-S-2.06Solar tracker
joe-skb7
135.9 × 47 mm26 parts2LGPL-3.06Tribus
pferreir
30 × 106 mm109 parts2LNo license5Hardware
xtarke
135.8 × 56.2 mm84 parts2LGPL-3.05Hardware
xtarke
135.8 × 56.2 mm84 parts2LNo license5EuroClack Formant LFO panel
clacktronics
70.8 × 128.5 mm101 parts2LNo license4Amplifier
MarinosK
99.1 × 99.1 mm69 parts2LNo license4Balancer
kwiecinski
99.5 × 99.5 mm165 parts2LMIT3STM32
LEDNip
MayaPosch
90 × 100 mm148 parts4LBSD-3-Clause3Noise toaster
samzeter
132.1 × 68.6 mm133 parts2LNo license3ESP32
TSAL G V4 2
HKUST-Red-Bird-Racing-EVRT
140 × 60 mm117 parts2LNo license3ESP32
Prototype Rev-
DiegoBriceno03
59.9 × 66.3 mm104 parts2LNo license3AVR/Arduino
CorboIron
bjohan
78.7 × 99.1 mm101 parts2LNo license3Microchip SAM
CatWAN Citizen
ElectronicCats
52 × 80 mm66 parts2LAGPL-3.03AutoPLC
dezamora98
208.9 × 119.9 mm358 parts2LNo license2Servo Motor Shield v1
cxxx1828
160 × 101.6 mm120 parts2LNo license2RP2040/RP2350
RP2040 Board
tystowell
88.3 × 65.4 mm55 parts2LCustom license2ESP32
Dc load
Fyfar
166.4 × 70.3 mm50 parts2LNo license2SVC-Circuits
oaklandsmartvehicles
85.3 × 80 mm32 parts2LNo license2Noise toaster
adeboni
128 × 129 mm133 parts2LGPL-3.01Solstrejf voiceboard core
KamikazeVildsvin
119.4 × 83.8 mm123 parts2LGPL-3.01AVR/Arduino
Main
ZeniteSolar
103.5 × 137.2 mm120 parts2LGPL-3.01CURRENT-SENSOR
zen451019
90 × 85 mm106 parts2LNo license1Opamp vos
cellularmitosis
99.7 × 49.5 mm94 parts2LMIT1
How designs wire the LM324
Read from the KiCad layouts of 119 open source designs, one per repository: what each pin of the LM324 connects to, and the resistors, capacitors and other passives placed on it.
- The - pins have a series resistor on 98 of 119 designs, most often 10 kΩ (then 1 kΩ).
- The 1OUT pin has a series resistor on 86 of 119 designs, most often 10 kΩ (then 1 kΩ).
- The + pins have a series resistor on 85 of 119 designs, most often 10 kΩ (then 100 kΩ).
- The 2OUT pin has a series resistor on 81 of 119 designs, most often 10 kΩ (then 1 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| 1OUTpin 1 | Connected to: A connector 23% |
|
| -pin 2, 6, 9, 13 | Connected to: Signal 83% |
|
| +pin 3, 5, 10, 12 | Connected to: Signal 79% |
|
| V+pin 4, 8 | Connected to: Signal 48% · 5V 45% |
|
| 2OUTpin 7 | Connected to: Signal 90% |
|
| V-pin 11 | Connected to: GND 64% · -12V 23% | — |
| 4OUTpin 14 | Connected to: Signal 73% · not connected 26% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Labrador by espotek-org, Snark barker by schlae, ZC95 MKII by CrashOverride85 and ALU by QuinnFreedman.
The LM324 in open source designs
The gallery holds 172 open source boards using the LM324 from 125 GitHub repositories; a typical one measures about 87.6 × 78.8 mm and carries around 69 components.
89% are two-layer designs, the rest use four layers or more, and 37% carry an open source license.
The most starred is Labrador by espotek-org.
Parts used alongside the LM324
Microcontrollers on boards using the LM324
What boards using the LM324 are built for
LM324: common questions
Where can I find a LM324 reference design?
Each of the 172 boards on this page is a real design using the LM324. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the LM324 - pin?
The - pins have a series resistor on 98 of 119 designs, most often 10 kΩ (then 1 kΩ). Counted from the KiCad layouts of 119 open source designs using the LM324.
What resistor goes on the LM324 1OUT pin?
The 1OUT pin has a series resistor on 86 of 119 designs, most often 10 kΩ (then 1 kΩ). Counted from the KiCad layouts of 119 open source designs using the LM324.
What resistor goes on the LM324 + pin?
The + pins have a series resistor on 85 of 119 designs, most often 10 kΩ (then 100 kΩ). Counted from the KiCad layouts of 119 open source designs using the LM324.
What parts are used alongside the LM324?
The LM393, L7805, AMS1117-3.3, LM358 and LM386 appear in the most repositories here.
Which microcontrollers do boards using the LM324 use?
Most are built on AVR/Arduino (18), ESP32 (11), STM32 (8) and RP2040/RP2350 (5).
How big is a typical board using the LM324?
The median is 87.6 × 78.8 mm, and 89% are two-layer designs.
What is the most popular open source board using the LM324?
By GitHub stars, Labrador by espotek-org, with 1,162 stars.
Can I simulate one of these boards using the LM324 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.