8 open source boards using the ADXL375

Real designs built with the ADXL375, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

8 boardsClear filters|Most starred

How designs wire the ADXL375

Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the ADXL375 connects to, and the resistors, capacitors and other passives placed on it.

  • The SCK/SCLK pin is tied to GND on 4 of 6 designs (a signal on 2).
  • The SDA/SDI/SDIO pin is left unconnected on 4 of 6 designs (a signal on 2).
  • The SDO/ALT_ADDRESS pin is tied to GND on 4 of 6 designs (a signal on 2).
  • The ~CS pin is tied to GND on 4 of 6 designs (a signal on 2).
SCK/SCLKpin 2Connected to: GND 67% · a signal 33%
SDA/SDI/SDIOpin 3Connected to: Not connected 67% · a signal 33%
SDO/ALT_ADDRESSpin 4Connected to: GND 67% · a signal 33%
~CSpin 5Connected to: GND 67% · a signal 33%
  • Pull-up to 3.3V on 33% · 4.7 kΩ (2)
VDDI/Opin 10Connected to: Not connected 67% · 3.3V 33%
RESGND_11pin 11Connected to: Not connected 100%

7 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include M2fc by cuspaceflight, THRValveControlModule by tokai-student-rocket-project, Radio by ojousima and Stm32logger by Birb-jpg.

The ADXL375 in open source designs

The gallery holds 8 open source boards using the ADXL375 from 7 GitHub repositories; a typical one measures about 35 × 70 mm and carries around 56 components.

57% use four copper layers or more, and 25% carry an open source license.

The most starred is M2fc by cuspaceflight.

Microcontrollers on boards using the ADXL375

What boards using the ADXL375 are built for

ADXL375: common questions

Where can I find a ADXL375 reference design?

Each of the 8 boards on this page is a real design using the ADXL375. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the ADXL375 SCK/SCLK pin connected?

The SCK/SCLK pin is tied to GND on 4 of 6 designs (a signal on 2). Counted from the KiCad layouts of 6 open source designs using the ADXL375.

How is the ADXL375 SDA/SDI/SDIO pin connected?

The SDA/SDI/SDIO pin is left unconnected on 4 of 6 designs (a signal on 2). Counted from the KiCad layouts of 6 open source designs using the ADXL375.

How is the ADXL375 SDO/ALT_ADDRESS pin connected?

The SDO/ALT_ADDRESS pin is tied to GND on 4 of 6 designs (a signal on 2). Counted from the KiCad layouts of 6 open source designs using the ADXL375.

What parts are used alongside the ADXL375?

The ATA6561, ICM_42688, MAX-M10S, MAX485E and MB85RQ8MX appear in the most repositories here.

Which microcontrollers do boards using the ADXL375 use?

Most are built on STM32 (5), AVR/Arduino (1), Renesas (1) and RP2040/RP2350 (1).

How big is a typical board using the ADXL375?

The median is 35 × 70 mm, and 43% are two-layer designs.

What is the most popular open source board using the ADXL375?

By GitHub stars, M2fc by cuspaceflight, with 5 stars.

Can I simulate one of these boards using the ADXL375 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part