12 open source boards using the ATA6561
Real designs built with the ATA6561, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Alturia
rckTom
45 × 24 mm96 parts4LCC-BY-NC-4.07STM32
NOGGIN
berkeleyauv
31.3 × 34 mm57 parts4LGPL-3.03AVR/Arduino
Logic
Keisuke063
50 × 50 mm43 parts4LNo license1STM32
FusIon Pack
Govish
162 × 154 mm319 parts4LMIT0ESP32
ESP32 SMD
syamei0
95 × 72 mm112 parts2LNo license0Thruster Controller V2
mark-belbin
35.5 × 37 mm102 parts4LGPL-3.043ESP32
ESP32 SMD
syamei0
95 × 72 mm113 parts2LNo license0Renesas
THRValveControlModule
tokai-student-rocket-project
99 × 75 mm46 parts2LNo license0STM32
ESCC
berkeleyauv
36 × 40 mm28 parts2LGPL-3.03STM32
THRValveControlModule
tokai-student-rocket-project
99 × 75 mm52 parts2LMIT2AVR/Arduino
ButtonInterfaceBoard 0-2
Govish
36.8 × 47 mm36 parts2LMIT0NOGLINK
berkeleyauv
19.5 × 30.8 mm22 parts2LGPL-3.03
How designs wire the ATA6561
Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the ATA6561 connects to, and the resistors, capacitors and other passives placed on it.
- The VDD pin has a decoupling capacitor on 8 of 9 designs, most often 100 nF (then 1 µF).
- The CANH pin has a series resistor on 6 of 9 designs, most often 120 Ω (then 100 Ω).
- The VIO pin has a decoupling capacitor on 5 of 9 designs, most often 100 nF.
- The STBY pin is tied to GND on 6 of 9 designs (a signal on 2).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VSSpin 2 | Connected to: GND 100% | — |
| VDDpin 3 | Connected to: 5V 100% |
|
| VIOpin 5 | Connected to: 3.3V 89% |
|
| CANLpin 6 | Connected to: A connector 100% |
|
| CANHpin 7 | Connected to: A connector 100% |
|
| STBYpin 8 | Connected to: GND 67% · a signal 22% | — |
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Thruster Controller V2 by mark-belbin, Alturia pcb by rckTom, ESCC by berkeleyauv and THRValveControlModule by tokai-student-rocket-project.
The ATA6561 in open source designs
The gallery holds 12 open source boards using the ATA6561 from 9 GitHub repositories; a typical one measures about 47.5 × 48.5 mm and carries around 55 components.
58% are two-layer designs, the rest use four layers or more, and 58% carry an open source license.
The most starred is Thruster Controller V2 by mark-belbin.
Parts used alongside the ATA6561
Microcontrollers on boards using the ATA6561
What boards using the ATA6561 are built for
ATA6561: common questions
Where can I find a ATA6561 reference design?
Each of the 12 boards on this page is a real design using the ATA6561. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the ATA6561 VDD pin?
The VDD pin has a decoupling capacitor on 8 of 9 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 9 open source designs using the ATA6561.
What resistor goes on the ATA6561 CANH pin?
The CANH pin has a series resistor on 6 of 9 designs, most often 120 Ω (then 100 Ω). Counted from the KiCad layouts of 9 open source designs using the ATA6561.
What decoupling capacitors do designs use on the ATA6561 VIO pin?
The VIO pin has a decoupling capacitor on 5 of 9 designs, most often 100 nF. Counted from the KiCad layouts of 9 open source designs using the ATA6561.
What parts are used alongside the ATA6561?
The CH340K, ADXL375, AZ1117CH-3.3TRG1, ESP32-WROOM-32E and ICM_42688 appear in the most repositories here.
Which microcontrollers do boards using the ATA6561 use?
Most are built on STM32 (5), AVR/Arduino (2), ESP32 (2) and Renesas (1).
How big is a typical board using the ATA6561?
The median is 47.5 × 48.5 mm, and 58% are two-layer designs.
What is the most popular open source board using the ATA6561?
By GitHub stars, Thruster Controller V2 by mark-belbin, with 43 stars.
Can I simulate one of these boards using the ATA6561 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.