9 open source boards using the AP62301WU-7
Real designs built with the AP62301WU-7, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Raspberry Pi
Scalenode cm4-baseboard
antmicro
128.5 × 40 mm125 parts4LApache-2.0151Gmsl deserializer
antmicro
75 × 60 mm225 parts4LApache-2.040- schematic only · 100 parts
Cm4-baseboard
antmicro
100 partsApache-2.036 Gmsl serializer
antmicro
43 × 43 mm98 parts4LApache-2.024D1600e psu breakout
antmicro
100 × 100 mm166 parts4LApache-2.020Dc scm breakout board
antmicro
108 × 70 mm274 parts6LApache-2.09RP2040/RP2350
Audio latency tester board
antmicro
80 × 40 mm201 parts4LApache-2.01Dc sci debug interposer
antmicro
90 × 68 mm257 parts8LApache-2.00ESP32
Hw thingcell
GuilleGonzzalez
32.5 × 67 mm81 parts4LNo license0
How designs wire the AP62301WU-7
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the AP62301WU-7 connects to, and the resistors, capacitors and other passives placed on it.
- The SW pin has a series capacitor on 8 of 8 designs, most often 100 nF.
- The SW pin has a inductor on 8 of 8 designs, most often 3.3 µH.
- The VIN pin has a decoupling capacitor on 8 of 8 designs, most often 10 µF.
- The FB pin has a resistor to GND on 8 of 8 designs, most often 10 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1 | Connected to: GND 100% | — |
| SWpin 2 | Connected to: Signal 100% |
|
| VINpin 3 | Connected to: 12V 88% |
|
| FBpin 4 | Connected to: Signal 100% |
|
| ENpin 5 | Connected to: Signal 88% |
|
| BSTpin 6 | Connected to: Signal 100% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Scalenode cm4-baseboard by antmicro, Gmsl deserializer by antmicro, Gmsl serializer by antmicro and D1600e psu breakout by antmicro.
The AP62301WU-7 in open source designs
The gallery holds 9 open source boards using the AP62301WU-7 from 9 GitHub repositories; a typical one measures about 85 × 63.5 mm and carries around 166 components.
100% use four copper layers or more, and 89% carry an open source license.
The most starred is Scalenode cm4-baseboard by antmicro.
Parts used alongside the AP62301WU-7
Microcontrollers on boards using the AP62301WU-7
What boards using the AP62301WU-7 are built for
AP62301WU-7: common questions
Where can I find a AP62301WU-7 reference design?
Each of the 9 boards on this page is a real design using the AP62301WU-7. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the AP62301WU-7 SW pin connected?
The SW pin has a series capacitor on 8 of 8 designs, most often 100 nF. Counted from the KiCad layouts of 8 open source designs using the AP62301WU-7.
What decoupling capacitors do designs use on the AP62301WU-7 VIN pin?
The VIN pin has a decoupling capacitor on 8 of 8 designs, most often 10 µF. Counted from the KiCad layouts of 8 open source designs using the AP62301WU-7.
What resistor goes on the AP62301WU-7 FB pin?
The FB pin has a resistor to GND on 8 of 8 designs, most often 10 kΩ. Counted from the KiCad layouts of 8 open source designs using the AP62301WU-7.
Which microcontrollers do boards using the AP62301WU-7 use?
Most are built on ESP32 (1), Raspberry Pi (1) and RP2040/RP2350 (1).
How big is a typical board using the AP62301WU-7?
The median is 85 × 63.5 mm, and 0% are two-layer designs.
What is the most popular open source board using the AP62301WU-7?
By GitHub stars, Scalenode cm4-baseboard by antmicro, with 151 stars.
Can I simulate one of these boards using the AP62301WU-7 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.