13 open source boards using the AP22615AWU-7
Real designs built with the AP22615AWU-7, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
RP2040/RP2350
X1Plus Expander X1P-002
jwise
145 × 57 mm134 parts4LNo license50Gmsl deserializer
antmicro
75 × 60 mm225 parts4LApache-2.040- schematic only · 100 parts
Cm4-baseboard
antmicro
100 partsApache-2.036 Dc scm breakout board
antmicro
108 × 70 mm274 parts6LApache-2.09STM32
Moducard cm5-module
Dominik-Workshop
100 × 100 mm246 parts4LMIT5Sdi fiber adapter
antmicro
70 × 42 mm140 parts4LApache-2.05Job storage expansion
antmicro
39.5 × 96.3 mm83 parts4LApache-2.04PCIe-DMA-DDR3-Accelerator
regymm
171.5 × 243.8 mm341 parts4LNo license1ESP32
Fibel2
nikolozka
210 × 148 mm434 parts4LNo license0Job pcie switch expansion
antmicro
100 × 60 mm297 parts6LApache-2.00STM32
PC ExtensionBoard
caotiendattx
128.3 × 98.3 mm263 parts6LNo license0ESP32
KicadReleaseCI
lukasznowarkiewicz
28 × 20.1 mm49 parts4LGPL-2.00STM32
BlackPanda
lukasloetkolben
47.5 × 41.7 mm86 parts4LMIT92
How designs wire the AP22615AWU-7
Read from the KiCad layouts of 12 open source designs, one per repository: what each pin of the AP22615AWU-7 connects to, and the resistors, capacitors and other passives placed on it.
- The OUT pin has a capacitor to GND on 12 of 12 designs, most often 100 nF (then 1 µF).
- The ISET pin has a resistor to GND on 12 of 12 designs, most often 2.4 kΩ (then 6.8 kΩ).
- The FLG pin has a pull-up to 5V on 9 of 12 designs, most often 10 kΩ.
- The IN pin is tied to 5V on 10 of 12 designs (a signal on 2).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| OUTpin 1 | Connected to: A connector 33% · 3.3V 42% |
|
| GNDpin 2 | Connected to: GND 100% | — |
| FLGpin 3 | Connected to: Signal 92% |
|
| ENpin 4 | Connected to: Signal 92% |
|
| ISETpin 5 | Connected to: Signal 100% |
|
| INpin 6 | Connected to: 5V 83% · a signal 17% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include BlackPanda by lukasloetkolben, X1Plus Expander X1P-002 by jwise, Gmsl deserializer by antmicro and Dc scm breakout board by antmicro.
The AP22615AWU-7 in open source designs
The gallery holds 13 open source boards using the AP22615AWU-7 from 13 GitHub repositories; a typical one measures about 100 × 65 mm and carries around 225 components.
100% use four copper layers or more, and 69% carry an open source license.
The most starred is BlackPanda by lukasloetkolben.
Parts used alongside the AP22615AWU-7
Microcontrollers on boards using the AP22615AWU-7
What boards using the AP22615AWU-7 are built for
AP22615AWU-7: common questions
Where can I find a AP22615AWU-7 reference design?
Each of the 13 boards on this page is a real design using the AP22615AWU-7. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the AP22615AWU-7 OUT pin connected?
The OUT pin has a capacitor to GND on 12 of 12 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 12 open source designs using the AP22615AWU-7.
What resistor goes on the AP22615AWU-7 ISET pin?
The ISET pin has a resistor to GND on 12 of 12 designs, most often 2.4 kΩ (then 6.8 kΩ). Counted from the KiCad layouts of 12 open source designs using the AP22615AWU-7.
What pull-up resistor is used on the AP22615AWU-7 FLG pin?
The FLG pin has a pull-up to 5V on 9 of 12 designs, most often 10 kΩ. Counted from the KiCad layouts of 12 open source designs using the AP22615AWU-7.
What parts are used alongside the AP22615AWU-7?
The AP62301WU-7, 93AA66C-I/SN, FT230XQ-R, SIC431AED-T1-GE3 and TPD4E05U06QDQARQ1 appear in the most repositories here.
Which microcontrollers do boards using the AP22615AWU-7 use?
Most are built on STM32 (3), ESP32 (2) and RP2040/RP2350 (1).
How big is a typical board using the AP22615AWU-7?
The median is 100 × 65 mm, and 0% are two-layer designs.
What is the most popular open source board using the AP22615AWU-7?
By GitHub stars, BlackPanda by lukasloetkolben, with 92 stars.
Can I simulate one of these boards using the AP22615AWU-7 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.