5 open source boards using the AP63203
Real designs built with the AP63203, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Elec Anything2EtherCAT
pollen-robotics
60 × 70.3 mm200 parts4LApache-2.04Sick spider
alangecker
137 × 76.7 mm120 parts2LGPL-3.01RP2040/RP2350
ICEPico
SorenGilkeyJohnson
21 × 51 mm69 parts4LCERN-OHL-S-2.01RP2040/RP2350
Elec Ventouse 3d
pollen-robotics
45 × 64 mm132 parts4LApache-2.00Elec Ventouse 2d
pollen-robotics
50 × 65 mm121 parts4LApache-2.00
How designs wire the AP63203
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the AP63203 connects to, and the resistors, capacitors and other passives placed on it.
- The SW pin has a series capacitor on 5 of 5 designs, most often 100 nF.
- The SW pin has a inductor on 5 of 5 designs, most often 6.8 µH (then 3.9 µH).
- The BST pin has a series capacitor on 5 of 5 designs, most often 100 nF.
- The EN pin is tied to VBUS on 5 of 5 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| FBpin 1 | Connected to: 3.3V 80% · a signal 20% |
|
| ENpin 2 | Connected to: VBUS 100% | — |
| INpin 3 | Connected to: VBUS 100% | — |
| GNDpin 4 | Connected to: GND 100% | — |
| SWpin 5 | Connected to: Signal 100% |
|
| BSTpin 6 | Connected to: Signal 100% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Elec Anything2EtherCAT by pollen-robotics, Sick spider by alangecker, ICEPico by SorenGilkeyJohnson and Elec Ventouse 2d by pollen-robotics.
The AP63203 in open source designs
The gallery holds 5 open source boards using the AP63203 from 5 GitHub repositories; a typical one measures about 50 × 65 mm and carries around 121 components.
80% use four copper layers or more, and 100% carry an open source license.
The most starred is Elec Anything2EtherCAT by pollen-robotics.
Parts used alongside the AP63203
Microcontrollers on boards using the AP63203
What boards using the AP63203 are built for
AP63203: common questions
Where can I find a AP63203 reference design?
Each of the 5 boards on this page is a real design using the AP63203. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the AP63203 SW pin connected?
The SW pin has a series capacitor on 5 of 5 designs, most often 100 nF. Counted from the KiCad layouts of 5 open source designs using the AP63203.
How is the AP63203 BST pin connected?
The BST pin has a series capacitor on 5 of 5 designs, most often 100 nF. Counted from the KiCad layouts of 5 open source designs using the AP63203.
How is the AP63203 EN pin connected?
The EN pin is tied to VBUS on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the AP63203.
Which microcontrollers do boards using the AP63203 use?
Most are built on RP2040/RP2350 (2) and STM32 (1).
How big is a typical board using the AP63203?
The median is 50 × 65 mm, and 20% are two-layer designs.
What is the most popular open source board using the AP63203?
By GitHub stars, Elec Anything2EtherCAT by pollen-robotics, with 4 stars.
Can I simulate one of these boards using the AP63203 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.