6 open source boards using the AT24CS32-STUM
Real designs built with the AT24CS32-STUM, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Microchip SAM
SensebenderGW
mysensors
50 × 50 mm70 parts2LNo license7AVR/Arduino
Mender shield
joelguittet
65 × 59 mm35 parts2LApache-2.05STM32
Spha btni hardware
sillevl
103 × 86.5 mm112 parts2LNo license0STM32
Spha rel12-hardware
sillevl
207.5 × 86.5 mm89 parts2LNo license0STM32
Spha rel6-hardware
sillevl
103 × 86.5 mm70 parts2LNo license0Rpi sa8x8hat
charlieh0tel
65 × 56.5 mm67 parts4LBSD-3-Clause0
How designs wire the AT24CS32-STUM
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the AT24CS32-STUM connects to, and the resistors, capacitors and other passives placed on it.
- The SCL pin has a pull-up to 3.3V on 6 of 6 designs, most often 10 kΩ (then 4.7 kΩ).
- The SDA pin has a pull-up to 3.3V on 6 of 6 designs, most often 10 kΩ (then 4.7 kΩ).
- The VCC pin has a decoupling capacitor on 5 of 6 designs, most often 100 nF.
- The WP pin is tied to GND on 4 of 6 designs (a signal on 2).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| SCLpin 1 | Connected to: A connector 100%, the microcontroller 67%, TCA9555RTWR 50% |
|
| GNDpin 2 | Connected to: GND 100% | — |
| SDApin 3 | Connected to: A connector 100%, the microcontroller 67%, TCA9555RTWR 50% |
|
| VCCpin 4 | Connected to: 3.3V 100% |
|
| WPpin 5 | Connected to: GND 67% · a signal 33% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include SensebenderGW by mysensors, Mender shield by joelguittet, Rpi sa8x8hat by charlieh0tel and Spha btni hardware by sillevl.
The AT24CS32-STUM in open source designs
The gallery holds 6 open source boards using the AT24CS32-STUM from 6 GitHub repositories; a typical one measures about 84 × 72.8 mm and carries around 70 components.
83% are two-layer designs, the rest use four layers or more, and 33% carry an open source license.
The most starred is SensebenderGW by mysensors.
Parts used alongside the AT24CS32-STUM
Microcontrollers on boards using the AT24CS32-STUM
What boards using the AT24CS32-STUM are built for
AT24CS32-STUM: common questions
Where can I find a AT24CS32-STUM reference design?
Each of the 6 boards on this page is a real design using the AT24CS32-STUM. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the AT24CS32-STUM SCL pin?
The SCL pin has a pull-up to 3.3V on 6 of 6 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 6 open source designs using the AT24CS32-STUM.
What pull-up resistor is used on the AT24CS32-STUM SDA pin?
The SDA pin has a pull-up to 3.3V on 6 of 6 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 6 open source designs using the AT24CS32-STUM.
What decoupling capacitors do designs use on the AT24CS32-STUM VCC pin?
The VCC pin has a decoupling capacitor on 5 of 6 designs, most often 100 nF. Counted from the KiCad layouts of 6 open source designs using the AT24CS32-STUM.
What parts are used alongside the AT24CS32-STUM?
The LM2594M-5.0, MCP1825S, PESD2CAN, SN65HVD230 and STM32L432KCUx appear in the most repositories here.
Which microcontrollers do boards using the AT24CS32-STUM use?
Most are built on STM32 (3), AVR/Arduino (1) and Microchip SAM (1).
How big is a typical board using the AT24CS32-STUM?
The median is 84 × 72.8 mm, and 83% are two-layer designs.
What is the most popular open source board using the AT24CS32-STUM?
By GitHub stars, SensebenderGW by mysensors, with 7 stars.
Can I simulate one of these boards using the AT24CS32-STUM before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.