6 open source boards using the ATmega8-16P

Real designs built with the ATmega8-16P, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

6 boardsClear filters|Most starred

How designs wire the ATmega8-16P

Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the ATmega8-16P connects to, and the resistors, capacitors and other passives placed on it.

  • The PC6/RESET pin has a pull-up to VCC on 5 of 6 designs, most often 10 kΩ.
  • The PB6/XTAL1 pin has a crystal on 4 of 6 designs, most often 16 MHz (then 8 MHz).
  • The PB7/XTAL2 pin has a crystal on 4 of 6 designs, most often 16 MHz (then 8 MHz).
  • The AREF pin has a capacitor to GND on 4 of 6 designs, most often 100 nF.
PC6/RESETpin 1Connected to: A connector 50%
  • Pull-up to VCC on 83% · 10 kΩ (5)
  • Capacitor to GND on 50% · 100 nF (2)
  • Series resistor on 33% · 330 Ω (1), 10 kΩ (1)
VCCpin 7Connected to: VCC 83% · a signal 17%
  • Decoupling capacitor on 50% · 100 nF (2), 1 µF (1)
GNDpin 8Connected to: GND 83% · a signal 17%
PB6/XTAL1pin 9Connected to: Signal 67% · not connected 33%
  • Crystal on 67% · 16 MHz (2), 8 MHz (1)
  • Capacitor to GND on 50% · 22 pF (2)
PB7/XTAL2pin 10Connected to: Signal 67% · not connected 33%
  • Crystal on 67% · 16 MHz (2), 8 MHz (1)
  • Capacitor to GND on 50% · 22 pF (2)
PB3pin 17Connected to: A connector 50% · not connected 33%
  • Series resistor on 33% · 5.6 kΩ (1), 330 Ω (1)
AREFpin 21Connected to: Signal 67% · not connected 33%
  • Capacitor to GND on 67% · 100 nF (3)
AGNDpin 22Connected to: GND 67% · not connected 17% · a signal 17%
PC1pin 24Connected to: 74HC244 33%, 74HC373 33%, CY62256-70PC 33% · not connected 17%
  • Series resistor on 33% · 1 kΩ (2)
PC2pin 25Connected to: CY62256-70PC 33% · not connected 17%
  • Series resistor on 33% · 1 kΩ (1), 330 kΩ (1)

18 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Emuprom by agkaminski, Dz TapeDelay Control by dzavalishin, Emuprom by agkaminski and Electronic load by ondras12345.

The ATmega8-16P in open source designs

The gallery holds 6 open source boards using the ATmega8-16P from 6 GitHub repositories; a typical one measures about 66.2 × 56.7 mm and carries around 34 components.

100% are two-layer designs, the rest use four layers or more, and 50% carry an open source license.

The most starred is Dz TapeDelay Control by dzavalishin.

Parts used alongside the ATmega8-16P

Microcontrollers on boards using the ATmega8-16P

ATmega8-16P: common questions

Where can I find a ATmega8-16P reference design?

Each of the 6 boards on this page is a real design using the ATmega8-16P. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What pull-up resistor is used on the ATmega8-16P PC6/RESET pin?

The PC6/RESET pin has a pull-up to VCC on 5 of 6 designs, most often 10 kΩ. Counted from the KiCad layouts of 6 open source designs using the ATmega8-16P.

How is the ATmega8-16P PB6/XTAL1 pin connected?

The PB6/XTAL1 pin has a crystal on 4 of 6 designs, most often 16 MHz (then 8 MHz). Counted from the KiCad layouts of 6 open source designs using the ATmega8-16P.

How is the ATmega8-16P PB7/XTAL2 pin connected?

The PB7/XTAL2 pin has a crystal on 4 of 6 designs, most often 16 MHz (then 8 MHz). Counted from the KiCad layouts of 6 open source designs using the ATmega8-16P.

What parts are used alongside the ATmega8-16P?

The 74HC244, 74HC32, 74HC373, CH340N and CY62256-70PC appear in the most repositories here.

Which microcontrollers do boards using the ATmega8-16P use?

Most are built on AVR/Arduino (6).

How big is a typical board using the ATmega8-16P?

The median is 66.2 × 56.7 mm, and 100% are two-layer designs.

What is the most popular open source board using the ATmega8-16P?

By GitHub stars, Dz TapeDelay Control by dzavalishin, with 3 stars.

Can I simulate one of these boards using the ATmega8-16P before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part