10 open source boards using the ATSAMD21E

Real designs built with the ATSAMD21E, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

10 boardsClear filters|Most starred

How designs wire the ATSAMD21E

Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the ATSAMD21E connects to, and the resistors, capacitors and other passives placed on it.

  • Pin 29 has a capacitor to GND on 6 of 7 designs, most often 1 µF (then 100 nF).
  • Pin 10 is tied to GND on 7 of 7 designs.
  • Pin 28 is tied to GND on 7 of 7 designs.
  • Pin 9 is tied to 3.3V on 6 of 7 designs.
Pin 3Connected to: Signal 86%
  • Series resistor on 43% · 10 MΩ (1), 0 Ω (1), 1.1 kΩ (1)
Pin 9Connected to: 3.3V 86%
  • Decoupling capacitor on 43% · 100 nF (3), 10 µF (1)
Pin 10Connected to: GND 100%
Pin 13Connected to: A connector 29%
  • Series resistor on 57% · 1.5 kΩ (2), 10 kΩ (1), 1.1 kΩ (1)
Pin 15Connected to: Signal 71% · not connected 29%
  • Series resistor on 43% · 330 Ω (1), 1.1 kΩ (1), 120 Ω (1)
Pin 28Connected to: GND 100%
Pin 29Connected to: Signal 71% · VDDCORE 29%
  • Capacitor to GND on 86% · 1 µF (6), 100 nF (1)
Pin 30Connected to: 3.3V 86%
  • Decoupling capacitor on 57% · 100 nF (3), 1 µF (1), 10 µF (1)
Pin 33Connected to: GND 100%

24 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include EL driver multi by benkrasnow, Nigun by raziele, DSKY-alarm panel replica by rrainey and CatWAN Relay by ElectronicCats.

The ATSAMD21E in open source designs

The gallery holds 10 open source boards using the ATSAMD21E from 7 GitHub repositories; a typical one measures about 68.7 × 50.4 mm and carries around 51 components.

86% are two-layer designs, the rest use four layers or more, and 10% carry an open source license.

The most starred is EL driver multi by benkrasnow.

Parts used alongside the ATSAMD21E

Microcontrollers on boards using the ATSAMD21E

What boards using the ATSAMD21E are built for

ATSAMD21E: common questions

Where can I find a ATSAMD21E reference design?

Each of the 10 boards on this page is a real design using the ATSAMD21E. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the ATSAMD21E pin 29 connected?

Pin 29 has a capacitor to GND on 6 of 7 designs, most often 1 µF (then 100 nF). Counted from the KiCad layouts of 7 open source designs using the ATSAMD21E.

How is the ATSAMD21E pin 10 connected?

Pin 10 is tied to GND on 7 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the ATSAMD21E.

How is the ATSAMD21E pin 28 connected?

Pin 28 is tied to GND on 7 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the ATSAMD21E.

What parts are used alongside the ATSAMD21E?

The AP2112K-3.3, AQY232SZ and RFM95W-868S2 appear in the most repositories here.

Which microcontrollers do boards using the ATSAMD21E use?

Most are built on Microchip SAM (10).

How big is a typical board using the ATSAMD21E?

The median is 68.7 × 50.4 mm, and 86% are two-layer designs.

What is the most popular open source board using the ATSAMD21E?

By GitHub stars, EL driver multi by benkrasnow, with 101 stars.

Can I simulate one of these boards using the ATSAMD21E before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part