13 open source boards using the ATTINY44A-MMH

Real designs built with the ATTINY44A-MMH, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

13 boardsClear filters|Most starred

How designs wire the ATTINY44A-MMH

Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the ATTINY44A-MMH connects to, and the resistors, capacitors and other passives placed on it.

  • The PA3 pin is left unconnected on 6 of 6 designs.
  • The AREF/PA0 pin has a pull-up to 3.3V on 5 of 6 designs, most often 10 kΩ.
  • The VCC pin has a decoupling capacitor on 5 of 6 designs, most often 100 nF (then 1 µF).
  • The PA2 pin is left unconnected on 5 of 6 designs.
PA3pin 2Connected to: Not connected 100%
PA2pin 3Connected to: Not connected 83% · a signal 17%
PA1pin 4Connected to: Not connected 83% · a signal 17%
AREF/PA0pin 5Connected to: A connector 83% · GND 17%
  • Pull-up to 3.3V on 83% · 10 kΩ (5)
NCpin 6, 7, 10, 17, 18, 19Connected to: Not connected 84%
GNDpin 8, 21Connected to: GND 83%
VCCpin 9Connected to: 3.3V 83% · a signal 17%
  • Decoupling capacitor on 83% · 100 nF (5), 1 µF (2)
XTAL1/PB0pin 11Connected to: Not connected 83% · a signal 17%
XTAL2/PB1pin 12Connected to: Not connected 83% · a signal 17%
PB2pin 14Connected to: Not connected 83% · a signal 17%
PA7pin 15Connected to: Not connected 83% · a signal 17%

4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Dual Atto320 breakout by gregdavill, CAN Breakout by gregdavill, Syzygy breakout standard by butterstick-fpga and Syzygy breakout flash-LVL by adamcritchley.

The ATTINY44A-MMH in open source designs

The gallery holds 13 open source boards using the ATTINY44A-MMH from 6 GitHub repositories; a typical one measures about 45 × 70 mm and carries around 33 components.

100% use four copper layers or more, and 23% carry an open source license.

The most starred is EPC Breakout by gregdavill.

Parts used alongside the ATTINY44A-MMH

Microcontrollers on boards using the ATTINY44A-MMH

What boards using the ATTINY44A-MMH are built for

ATTINY44A-MMH: common questions

Where can I find a ATTINY44A-MMH reference design?

Each of the 13 boards on this page is a real design using the ATTINY44A-MMH. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the ATTINY44A-MMH PA3 pin connected?

The PA3 pin is left unconnected on 6 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the ATTINY44A-MMH.

What pull-up resistor is used on the ATTINY44A-MMH AREF/PA0 pin?

The AREF/PA0 pin has a pull-up to 3.3V on 5 of 6 designs, most often 10 kΩ. Counted from the KiCad layouts of 6 open source designs using the ATTINY44A-MMH.

What decoupling capacitors do designs use on the ATTINY44A-MMH VCC pin?

The VCC pin has a decoupling capacitor on 5 of 6 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 6 open source designs using the ATTINY44A-MMH.

Which microcontrollers do boards using the ATTINY44A-MMH use?

Most are built on AVR/Arduino (13).

How big is a typical board using the ATTINY44A-MMH?

The median is 45 × 70 mm, and 0% are two-layer designs.

What is the most popular open source board using the ATTINY44A-MMH?

By GitHub stars, EPC Breakout by gregdavill, with 178 stars.

Can I simulate one of these boards using the ATTINY44A-MMH before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part