9 open source boards using the Battery
Real designs built with the Battery, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
MainBoard
andresR8
55.6 × 64 mm41 parts2LNo license5ESP32
Linefollowingrobot
msafeerhassan
130.5 × 169.5 mm11 parts2LNo license1RP2040/RP2350
Esp32-gps
yvolodym
50 × 50 mm59 parts4LCERN-OHL-S-2.00ESP32
Esp32-controller
yvolodym
100 × 70 mm51 parts4LNo license0Timemaster2ho
mtnofcode
119.4 × 76.2 mm17 parts4LCC-BY-SA-4.00- schematic only · 34 partsESP32
Bugsy
SamuelNoesslboeck
34 partsCERN-OHL-P-2.00 AVR/Arduino
Mainboard
ARTS-Laboratory
41.9 × 55.9 mm12 parts2LCC-BY-SA-4.02AVR/Arduino
Water sensor1
ARTS-Laboratory
48.3 × 58.4 mm11 parts2LCC-BY-SA-4.02AVR/Arduino
Water Quality Sensor
ARTS-Laboratory
44 × 58.5 mm8 parts2LCC-BY-SA-4.02
How designs wire the Battery
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the Battery connects to, and the resistors, capacitors and other passives placed on it.
- The + pin has a series resistor on 2 of 5 designs, most often 220 kΩ (then 100 Ω).
- The + pin has a capacitor to GND on 2 of 5 designs, most often 10 µF.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| +pin 1 | Connected to: LTC4412 40%, TP4056-42-ESOP8 40% · GND 20% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Mainboard by ARTS-Laboratory, Linefollowingrobot by msafeerhassan, Timemaster2ho by mtnofcode and Esp32-controller by yvolodym.
The Battery in open source designs
The gallery holds 9 open source boards using the Battery from 7 GitHub repositories; a typical one measures about 52.8 × 61.2 mm and carries around 17 components.
63% are two-layer designs, the rest use four layers or more, and 67% carry an open source license.
The most starred is MainBoard by andresR8.
Parts used alongside the Battery
Microcontrollers on boards using the Battery
What boards using the Battery are built for
Battery: common questions
Where can I find a Battery reference design?
Each of the 9 boards on this page is a real design using the Battery. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the Battery + pin?
The + pin has a series resistor on 2 of 5 designs, most often 220 kΩ (then 100 Ω). Counted from the KiCad layouts of 5 open source designs using the Battery.
What parts are used alongside the Battery?
The Switch, AP2112K-3.3, DW01A, LTC4412 and TP4056-42-ESOP8 appear in the most repositories here.
Which microcontrollers do boards using the Battery use?
Most are built on AVR/Arduino (4), ESP32 (3) and RP2040/RP2350 (1).
How big is a typical board using the Battery?
The median is 52.8 × 61.2 mm, and 63% are two-layer designs.
What is the most popular open source board using the Battery?
By GitHub stars, MainBoard by andresR8, with 5 stars.
Can I simulate one of these boards using the Battery before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.