10 open source boards using the BOB-12009
Real designs built with the BOB-12009, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP8266
Placa todo en uno
NicolasSchkurko
176.3 × 208.8 mm50 parts2LNo license1ESP32
WRO FE 2026 FoxRobotics
Nakashima26
87.2 × 93.9 mm20 parts2LMIT1ESP32
Esp32 keyboard
tigmit
344.5 × 125.4 mm179 parts2LNo license0NXP
Guepard one
IlyaasAitSimmou
85 × 85 mm21 parts4LNo license0ESP32
Trotten
Oberson-Antoine
75.8 × 60.4 mm20 parts2LNo license0ESP8266
Proyecto V2
NicolasSchkurko
89.9 × 85.7 mm47 parts2LNo license1ESP32
PCB MainBoard
Oberson-Antoine
75.8 × 60.4 mm10 parts2LNo license0AVR/Arduino
Filter shield
OE9SAU
101.6 × 53.4 mm27 parts2LNo license4ESP32
RF rec trans v2
bostang
64.7 × 133.2 mm15 parts2LNo license0AVR/Arduino
Placa main ESPtestsocket
NicolasSchkurko
86.1 × 88.2 mm17 parts2LNo license1
How designs wire the BOB-12009
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the BOB-12009 connects to, and the resistors, capacitors and other passives placed on it.
- The HV pin is tied to 5V on 4 of 6 designs (a signal on 2).
- The LV pin is tied to 3.3V on 4 of 6 designs (a signal on 2).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin GND_1, GND_2 | Connected to: GND 83% · a signal 17% | — |
| HVpin HV | Connected to: 5V 67% · a signal 33% | — |
| LVpin LV | Connected to: 3.3V 67% · a signal 33% | — |
8 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Filter shield by OE9SAU, WRO FE 2026 FoxRobotics by Nakashima26, Placa main ESPtestsocket by NicolasSchkurko and RF rec trans v2 by bostang.
The BOB-12009 in open source designs
The gallery holds 10 open source boards using the BOB-12009 from 7 GitHub repositories; a typical one measures about 86.6 × 86.9 mm and carries around 21 components.
90% are two-layer designs, the rest use four layers or more, and 10% carry an open source license.
The most starred is Filter shield by OE9SAU.
Microcontrollers on boards using the BOB-12009
What boards using the BOB-12009 are built for
BOB-12009: common questions
Where can I find a BOB-12009 reference design?
Each of the 10 boards on this page is a real design using the BOB-12009. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the BOB-12009 HV pin connected?
The HV pin is tied to 5V on 4 of 6 designs (a signal on 2). Counted from the KiCad layouts of 7 open source designs using the BOB-12009.
How is the BOB-12009 LV pin connected?
The LV pin is tied to 3.3V on 4 of 6 designs (a signal on 2). Counted from the KiCad layouts of 7 open source designs using the BOB-12009.
Which microcontrollers do boards using the BOB-12009 use?
Most are built on ESP32 (5), AVR/Arduino (2), ESP8266 (2) and NXP (1).
How big is a typical board using the BOB-12009?
The median is 86.6 × 86.9 mm, and 90% are two-layer designs.
What is the most popular open source board using the BOB-12009?
By GitHub stars, Filter shield by OE9SAU, with 4 stars.
Can I simulate one of these boards using the BOB-12009 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.