10 open source boards using the BP

Real designs built with the BP, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

10 boardsClear filters|Most starred

How designs wire the BP

Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the BP connects to, and the resistors, capacitors and other passives placed on it.

  • The RESET pin is left unconnected on 6 of 6 designs.
  • The PC13 pin is left unconnected on 6 of 7 designs.
  • The PA11 pin is left unconnected on 5 of 7 designs (a signal on 2).
  • The PA12 pin is left unconnected on 5 of 7 designs (a signal on 2).
3.3Vpin 3V3Connected to: 3.3V 67% · not connected 33%
GNDpin GConnected to: GND 100%
RESETpin NRSTConnected to: Not connected 100%
PA0pin PA0Connected to: Signal 71% · not connected 29%
  • Series resistor on 43% · 1 kΩ (2), 120 kΩ (1)
PA1pin PA1Connected to: Signal 86%
  • Series resistor on 57% · 1 kΩ (2), 100 Ω (1), 120 kΩ (1)
PA3pin PA3Connected to: Signal 86%
  • Series resistor on 43% · 1 kΩ (2), 30 kΩ (1)
PA11pin PA11Connected to: Not connected 71% · a signal 29%
PA12pin PA12Connected to: Not connected 71% · a signal 29%
PB0pin PB0Connected to: Signal 86%
  • Series resistor on 43% · 2.2 kΩ (1), 100 kΩ (1), 1 kΩ (1)
PB1pin PB1Connected to: Signal 86%
  • Series resistor on 43% · 2.2 kΩ (1), 100 kΩ (1), 1 kΩ (1)
PC13pin PC13Connected to: Not connected 86%
PC14pin PC14Connected to: Not connected 71% · a signal 29%
PC15pin PC15Connected to: Not connected 71% · a signal 29%
SWCLKpin SCK, SWCLKConnected to: Not connected 100%
SWOpin SWOConnected to: Not connected 100%
VBATpin VBATConnected to: Not connected 67% · 3.3V 33%

23 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include BionX Minimal Translator by stancecoke, Carga-Electronica-STM32 by kr4fty, Receiver by AdmondDeng and Esp bluepill board by ar216-2355.

The BP in open source designs

The gallery holds 10 open source boards using the BP from 8 GitHub repositories; a typical one measures about 79 × 58 mm and carries around 35 components.

78% are two-layer designs, the rest use four layers or more, and 10% carry an open source license.

The most starred is BionX Minimal Translator by stancecoke.

Microcontrollers on boards using the BP

BP: common questions

Where can I find a BP reference design?

Each of the 10 boards on this page is a real design using the BP. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the BP RESET pin connected?

The RESET pin is left unconnected on 6 of 6 designs. Counted from the KiCad layouts of 7 open source designs using the BP.

How is the BP PC13 pin connected?

The PC13 pin is left unconnected on 6 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the BP.

How is the BP PA11 pin connected?

The PA11 pin is left unconnected on 5 of 7 designs (a signal on 2). Counted from the KiCad layouts of 7 open source designs using the BP.

Which microcontrollers do boards using the BP use?

Most are built on ESP32 (2) and STM32 (2).

How big is a typical board using the BP?

The median is 79 × 58 mm, and 78% are two-layer designs.

What is the most popular open source board using the BP?

By GitHub stars, BionX Minimal Translator by stancecoke, with 21 stars.

Can I simulate one of these boards using the BP before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part