8 open source boards using the BQ25895RTWR

Real designs built with the BQ25895RTWR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

8 boardsClear filters|Most starred

How designs wire the BQ25895RTWR

Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the BQ25895RTWR connects to, and the resistors, capacitors and other passives placed on it.

  • The SCL pin has a pull-up to 3.3V on 7 of 7 designs, most often 10 kΩ (then 4.7 kΩ).
  • The SDA pin has a pull-up to 3.3V on 7 of 7 designs, most often 10 kΩ (then 4.7 kΩ).
  • The TS pin has a series resistor on 7 of 7 designs, most often 5.23 kΩ (then 10 kΩ).
  • The SYS pins have a capacitor to GND on 7 of 7 designs, most often 10 µF (then 100 nF).
VBUSpin 1Connected to: VBUS 71% · a signal 29%
  • Decoupling capacitor on 86% · 1 µF (5), 10 µF (3), 100 nF (2)
D+pin 2Connected to: Not connected 71% · a signal 29%
D–pin 3Connected to: Not connected 71% · a signal 29%
STATpin 4Connected to: Signal 86%
  • Series resistor on 43% · 2.2 kΩ (2), 330 Ω (1)
SCLpin 5Connected to: The microcontroller 86%
  • Pull-up to 3.3V on 100% · 10 kΩ (3), 4.7 kΩ (2), 2.2 kΩ (2)
SDApin 6Connected to: The microcontroller 86%
  • Pull-up to 3.3V on 100% · 10 kΩ (3), 4.7 kΩ (2), 2.2 kΩ (2)
INTpin 7Connected to: The microcontroller 57% · not connected 29%
  • Pull-up to 3.3V on 57% · 10 kΩ (4)
OTGpin 8Connected to: GND 71% · a signal 29%
CEpin 9Connected to: GND 86%
ILIMpin 10Connected to: Signal 86%
  • Resistor to GND on 86% · 270 Ω (1), 280 Ω (1), 100 Ω (1)
TSpin 11Connected to: A connector 29%
  • Series resistor on 100% · 5.23 kΩ (4), 10 kΩ (2), 5.1 kΩ (1)
  • Resistor to GND on 86% · 10 kΩ (4), 30.1 kΩ (2), 30 kΩ (2)
BATpin 13, 14Connected to: BATT 86%
  • Decoupling capacitor on 57% · 10 µF (8), 100 nF (2)
SYSpin 15, 16Connected to: Signal 71% · VSYS 29%
  • Capacitor to GND on 100% · 10 µF (31), 100 nF (6), 1 µF (6)
  • Inductor on 86% · 2.2 µH (10), 1 µH (2), 1.5 µH (2)
  • Series resistor on 43% · 100 kΩ (5), 100 Ω (2)
PGNDpin 17, 18Connected to: GND 100%
SWpin 19, 20Connected to: Signal 100%
  • Inductor on 100% · 2.2 µH (10), 1 µH (2), 1.5 µH (2)
  • Series capacitor on 100% · 47 nF (12), 100 nF (2)
BTSTpin 21Connected to: Signal 100%
  • Series capacitor on 100% · 47 nF (6), 100 nF (1)
REGNpin 22Connected to: Signal 100%
  • Capacitor to GND on 100% · 4.7 µF (6), 10 µF (1)
  • Series resistor on 100% · 5.23 kΩ (4), 10 kΩ (3), 5.1 kΩ (1)
PMIDpin 23Connected to: Signal 100%
  • Capacitor to GND on 100% · 10 µF (6), 22 µF (3), 47 µF (1)
PADpin 25Connected to: GND 100%

2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Monopoly-Electronic-V2 by Pegoku, PortaRe0 by 0Re0-8192, TyphoonMotherboard rev1 KiCad by hpvdt and Cryobelt by michael201110.

The BQ25895RTWR in open source designs

The gallery holds 8 open source boards using the BQ25895RTWR from 8 GitHub repositories; a typical one measures about 77 × 105.5 mm and carries around 93 components.

63% use four copper layers or more, and 13% carry an open source license.

The most starred is Monopoly-Electronic-V2 by Pegoku.

Microcontrollers on boards using the BQ25895RTWR

BQ25895RTWR: common questions

Where can I find a BQ25895RTWR reference design?

Each of the 8 boards on this page is a real design using the BQ25895RTWR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What pull-up resistor is used on the BQ25895RTWR SCL pin?

The SCL pin has a pull-up to 3.3V on 7 of 7 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 7 open source designs using the BQ25895RTWR.

What pull-up resistor is used on the BQ25895RTWR SDA pin?

The SDA pin has a pull-up to 3.3V on 7 of 7 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 7 open source designs using the BQ25895RTWR.

What resistor goes on the BQ25895RTWR TS pin?

The TS pin has a series resistor on 7 of 7 designs, most often 5.23 kΩ (then 10 kΩ). Counted from the KiCad layouts of 7 open source designs using the BQ25895RTWR.

What parts are used alongside the BQ25895RTWR?

The USBLC6-2SC6, AP2112K-3.3TRG1, ESP32-C3-WROOM-02-N4, MAX98357A and STUSB4500QTR appear in the most repositories here.

Which microcontrollers do boards using the BQ25895RTWR use?

Most are built on ESP32 (5) and RP2040/RP2350 (2).

How big is a typical board using the BQ25895RTWR?

The median is 77 × 105.5 mm, and 38% are two-layer designs.

What is the most popular open source board using the BQ25895RTWR?

By GitHub stars, Monopoly-Electronic-V2 by Pegoku, with 4 stars.

Can I simulate one of these boards using the BQ25895RTWR before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part