11 open source boards using the C16581
Real designs built with the C16581, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Kaleido 6" controller based on epdiy v7
vroland
138.1 × 104.6 mm121 parts4LCC-BY-SA-4.074ESP32
Cinread-IT8951 S3 HAT
martinberlin
83.2 × 42.1 mm54 parts2LCERN-OHL-W-2.012ESP8266
Models heart
KushlaVR
29.9 × 32 mm63 parts4LGPL-3.07Eink mahjong compass
ikuto0815
123.4 × 123.4 mm43 parts2LAGPL-3.03MkrfoxWindShield
pcaunegre
81.6 × 39.7 mm31 parts2LUnlicense2STM32
EEE3088F CKR backup
Carciax
90 × 75 mm132 parts2LMIT0ESP32
Open kinematic array
deanarvan
22 × 28 mm33 parts4LMIT0- schematic only · 42 partsESP32
Watch
Resteral
42 partsNo license0 ESP32
Epdiy v7
vroland
100 × 55 mm108 parts4LCC-BY-SA-4.074STM32
EEE3088F CKR backup2
Carciax
90 × 75 mm132 parts2LMIT0ESP32
Epdiy v7-raw
vroland
128.4 × 74.9 mm105 parts4LCC-BY-SA-4.074
How designs wire the C16581
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the C16581 connects to, and the resistors, capacitors and other passives placed on it.
- The PROG pin has a resistor to GND on 6 of 7 designs, most often 2 kΩ (then 6.8 kΩ).
- The TEMP pin is tied to GND on 6 of 7 designs.
- The VCC pin has a capacitor to GND on 5 of 7 designs, most often 10 µF (then 4.7 µF).
- The BAT pin is tied to BAT+ on 5 of 7 designs (a signal on 2).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| TEMPpin 1 | Connected to: GND 86% | — |
| PROGpin 2 | Connected to: Signal 100% |
|
| GNDpin 3 | Connected to: GND 100% | — |
| VCCpin 4 | Connected to: Signal 86% |
|
| BATpin 5 | Connected to: BAT+ 71% · a signal 29% |
|
| STDBYpin 6 | Connected to: Signal 71% |
|
| CHRGpin 7 | Connected to: Signal 71% |
|
| CEpin 8 | Connected to: Signal 86% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Epdiy v7 by vroland, Cinread-IT8951 S3 HAT by martinberlin, Models heart by KushlaVR and Eink mahjong compass by ikuto0815.
The C16581 in open source designs
The gallery holds 11 open source boards using the C16581 from 8 GitHub repositories; a typical one measures about 90 × 65 mm and carries around 63 components.
50% are two-layer designs, the rest use four layers or more, and 91% carry an open source license.
The most starred is Kaleido 6" controller based on epdiy v7 by vroland.
Parts used alongside the C16581
What boards using the C16581 are built for
C16581: common questions
Where can I find a C16581 reference design?
Each of the 11 boards on this page is a real design using the C16581. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the C16581 PROG pin?
The PROG pin has a resistor to GND on 6 of 7 designs, most often 2 kΩ (then 6.8 kΩ). Counted from the KiCad layouts of 7 open source designs using the C16581.
How is the C16581 TEMP pin connected?
The TEMP pin is tied to GND on 6 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the C16581.
How is the C16581 VCC pin connected?
The VCC pin has a capacitor to GND on 5 of 7 designs, most often 10 µF (then 4.7 µF). Counted from the KiCad layouts of 7 open source designs using the C16581.
Which microcontrollers do boards using the C16581 use?
Most are built on ESP32 (6), STM32 (2) and ESP8266 (1).
How big is a typical board using the C16581?
The median is 90 × 65 mm, and 50% are two-layer designs.
What is the most popular open source board using the C16581?
By GitHub stars, Kaleido 6" controller based on epdiy v7 by vroland, with 74 stars.
Can I simulate one of these boards using the C16581 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.