10 open source boards using the C7950
Real designs built with the C7950, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Main-Craft
LukeDWaller99
68.6 × 99.1 mm123 parts2LNo license1STM32
Pdk prog
brainsmoke
42 × 37 mm56 parts2LCC-BY-4.01STM32
CCTV3 F407 REV200
aiex718
70 × 80 mm220 parts4LNo license0STM32
PCB DRONE R8
ArduProject
102 × 49 mm150 parts4LMIT0Main-Craft
LukeDWaller99
68.6 × 99.1 mm123 parts2LNo license0ESP32
Probe
zuhayrl
50 × 50 mm73 parts4LNo license0AVR/Arduino
ORCA Control Board
LukeDWaller99
99.1 × 99.1 mm64 parts2LNo license1STM32
Megaboard Front V3
Kolmanpg
152.4 × 88.9 mm195 parts4LNo license0AVR/Arduino
ORCA Control Board
LukeDWaller99
99.1 × 99.1 mm64 parts2LNo license0ESP32
Megaboard Rear V3
Kolmanpg
155.3 × 110.3 mm180 parts4LNo license0
How designs wire the C7950
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the C7950 connects to, and the resistors, capacitors and other passives placed on it.
- The V- pin is tied to GND on 7 of 7 designs.
- The - pins have a resistor to GND on 5 of 7 designs, most often 40 kΩ (then 20 kΩ).
- The + pins have a resistor to GND on 5 of 7 designs, most often 100 kΩ (then 3.8 kΩ).
- The + pins have a series resistor on 5 of 7 designs, most often 300 Ω (then 3 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: A connector 29% |
|
| -pin 2, 6 | Connected to: Signal 79% |
|
| +pin 3, 5 | Connected to: Signal 71% |
|
| V-pin 4 | Connected to: GND 100% | — |
| Pin 7 | Connected to: A connector 29% · not connected 29% |
|
| V+pin 8 | Connected to: 5V 71% · a signal 29% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Pdk prog by brainsmoke, ORCA Control Board by LukeDWaller99, CCTV3 F407 REV200 by aiex718 and PCB DRONE R8 by ArduProject.
The C7950 in open source designs
The gallery holds 10 open source boards using the C7950 from 7 GitHub repositories; a typical one measures about 84.5 × 94 mm and carries around 123 components.
50% are two-layer designs, the rest use four layers or more, and 20% carry an open source license.
The most starred is Main-Craft-PCB by LukeDWaller99.
Parts used alongside the C7950
Microcontrollers on boards using the C7950
What boards using the C7950 are built for
C7950: common questions
Where can I find a C7950 reference design?
Each of the 10 boards on this page is a real design using the C7950. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the C7950 V- pin connected?
The V- pin is tied to GND on 7 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the C7950.
What resistor goes on the C7950 - pin?
The - pins have a resistor to GND on 5 of 7 designs, most often 40 kΩ (then 20 kΩ). Counted from the KiCad layouts of 7 open source designs using the C7950.
What resistor goes on the C7950 + pin?
The + pins have a resistor to GND on 5 of 7 designs, most often 100 kΩ (then 3.8 kΩ). Counted from the KiCad layouts of 7 open source designs using the C7950.
What parts are used alongside the C7950?
The C6186, C24112, C6187, Joystick and LM2940-12.0 appear in the most repositories here.
Which microcontrollers do boards using the C7950 use?
Most are built on STM32 (4), AVR/Arduino (2) and ESP32 (2).
How big is a typical board using the C7950?
The median is 84.5 × 94 mm, and 50% are two-layer designs.
What is the most popular open source board using the C7950?
By GitHub stars, Main-Craft-PCB by LukeDWaller99, with 1 stars.
Can I simulate one of these boards using the C7950 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.