13 open source boards using the C6187
Real designs built with the C6187, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Hw microdiff
aw
22.5 × 46 mm26 parts4LCC-BY-SA-4.09RP2040/RP2350
RP2040-DebugProbe
red-scorp
50.8 × 25.4 mm66 parts4LNo license8RP2040/RP2350
RP2040-Eins
red-scorp
68.6 × 53.3 mm64 parts4LNo license3AVR/Arduino
Halo
wyolum
243.8 × 66.3 mm152 parts2LApache-2.01ESP32
Airsoft bomb prop
makerspacelt
71.4 × 76.7 mm36 parts2LNo license1STM32
CCTV3 F407 REV200
aiex718
70 × 80 mm220 parts4LNo license0STM32
Micromouse
tadzio8425
99.3 × 98.9 mm97 parts4LMIT0AVR/Arduino
Ripple tank
practable
100 × 100 mm89 parts4LAGPL-3.00ESP32
Probe
zuhayrl
50 × 50 mm73 parts4LNo license0AVR/Arduino
25pix
bnaucler
60 × 96 mm60 parts2LMIT0ESP32
Controller
zuhayrl
55 × 70 mm22 parts2LNo license0Bt module
adeboni
10 × 108 mm46 parts2LGPL-3.01Analog to pwm
adeboni
10 × 104 mm51 parts2LGPL-3.00
How designs wire the C6187
Read from the KiCad layouts of 12 open source designs, one per repository: what each pin of the C6187 connects to, and the resistors, capacitors and other passives placed on it.
- The VI pin has a decoupling capacitor on 8 of 12 designs, most often 10 µF (then 100 nF).
- The VO pin has a decoupling capacitor on 5 of 12 designs, most often 100 nF (then 22 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1 | Connected to: GND 92% | — |
| VOpin 2 | Connected to: 5V 83% · a signal 17% |
|
| VIpin 3 | Connected to: 12V 58% · a signal 33% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Hw microdiff by aw, RP2040-DebugProbe by red-scorp, RP2040-Eins by red-scorp and Bt module by adeboni.
The C6187 in open source designs
The gallery holds 13 open source boards using the C6187 from 12 GitHub repositories; a typical one measures about 60 × 76.7 mm and carries around 64 components.
54% use four copper layers or more, and 54% carry an open source license.
The most starred is Hw microdiff by aw.
Parts used alongside the C6187
Microcontrollers on boards using the C6187
What boards using the C6187 are built for
C6187: common questions
Where can I find a C6187 reference design?
Each of the 13 boards on this page is a real design using the C6187. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the C6187 VI pin?
The VI pin has a decoupling capacitor on 8 of 12 designs, most often 10 µF (then 100 nF). Counted from the KiCad layouts of 12 open source designs using the C6187.
What decoupling capacitors do designs use on the C6187 VO pin?
The VO pin has a decoupling capacitor on 5 of 12 designs, most often 100 nF (then 22 µF). Counted from the KiCad layouts of 12 open source designs using the C6187.
What parts are used alongside the C6187?
The C6186, C2040, C2456297, C6961 and C7950 appear in the most repositories here.
Which microcontrollers do boards using the C6187 use?
Most are built on AVR/Arduino (3), ESP32 (3), RP2040/RP2350 (2) and STM32 (2).
How big is a typical board using the C6187?
The median is 60 × 76.7 mm, and 46% are two-layer designs.
What is the most popular open source board using the C6187?
By GitHub stars, Hw microdiff by aw, with 9 stars.
Can I simulate one of these boards using the C6187 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.