10 open source boards using the Joystick
Real designs built with the Joystick, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Iotuz esp32-hardware
CCHS-Melbourne
150 × 95 mm97 parts2LTAPR-OHL-1.035PZO System
nirim000
110 × 100 mm62 parts4LNo license1ESP32
AIR MOUSE
MAATHES-THILAK-K
41 × 69.4 mm29 parts2LApache-2.00ESP32
SnakeBoy
Nadoooor
180 × 85 mm22 parts2LMIT0HexMote
hephaestushex
90 × 40 mm12 parts2LGPL-3.00AVR/Arduino
ORCA Control Board
LukeDWaller99
99.1 × 99.1 mm64 parts2LNo license1AVR/Arduino
ORCA Control Board
LukeDWaller99
99.1 × 99.1 mm64 parts2LNo license0PCB panel
Mattkomi
100 × 80 mm26 parts2LNo license0Musashi50-rev8-wired
hamano
160 × 140 mm64 parts2LNo license27MinyasX-FrontPanel
kunichiko
96 × 21 mm17 parts4LMIT2
How designs wire the Joystick
Read from the KiCad layouts of 10 open source designs, one per repository: what each pin of the Joystick connects to, and the resistors, capacitors and other passives placed on it.
- Pin B1B is left unconnected on 4 of 4 designs.
- Pin B2B is left unconnected on 4 of 4 designs.
- The H+ pin is tied to 3.3V on 4 of 5 designs.
- The H- pin is tied to GND on 4 of 5 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin B1B | Connected to: Not connected 100% | — |
| SEL-pin B2A | Connected to: GND 75% · a signal 25% | — |
| Pin B2B | Connected to: Not connected 100% | — |
| H+pin H1 | Connected to: 3.3V 80% · a signal 20% | — |
| H-pin H3 | Connected to: GND 80% · a signal 20% | — |
| SHIELDpin S1, S2, S3, S4 | Connected to: GND 71% · a signal 24% | — |
| Pin SW1 | Connected to: Not connected 67% · a signal 33% | — |
| Pin SW2 | Connected to: Not connected 67% · GND 33% | — |
| V+pin V1 | Connected to: 3.3V 80% · a signal 20% | — |
| V-pin V3 | Connected to: GND 80% · a signal 20% | — |
| Pin X1 | Connected to: 3.3V 100% | — |
| Pin X2 | Connected to: Signal 100% |
|
| Pin X3 | Connected to: GND 100% | — |
| Pin Y1 | Connected to: 3.3V 67% · GND 33% | — |
| Pin Y2 | Connected to: Signal 100% |
|
| Pin Y3 | Connected to: GND 67% · 3.3V 33% | — |
3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Iotuz esp32-hardware by CCHS-Melbourne, Musashi50-rev8-wired by hamano, MinyasX-FrontPanel by kunichiko and ORCA Control Board by LukeDWaller99.
The Joystick in open source designs
The gallery holds 10 open source boards using the Joystick from 10 GitHub repositories; a typical one measures about 99.5 × 90 mm and carries around 46 components.
80% are two-layer designs, the rest use four layers or more, and 50% carry an open source license.
The most starred is Iotuz esp32-hardware by CCHS-Melbourne.
Parts used alongside the Joystick
Microcontrollers on boards using the Joystick
What boards using the Joystick are built for
Joystick: common questions
Where can I find a Joystick reference design?
Each of the 10 boards on this page is a real design using the Joystick. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the Joystick pin B1B connected?
Pin B1B is left unconnected on 4 of 4 designs. Counted from the KiCad layouts of 10 open source designs using the Joystick.
How is the Joystick pin B2B connected?
Pin B2B is left unconnected on 4 of 4 designs. Counted from the KiCad layouts of 10 open source designs using the Joystick.
How is the Joystick H+ pin connected?
The H+ pin is tied to 3.3V on 4 of 5 designs. Counted from the KiCad layouts of 10 open source designs using the Joystick.
What parts are used alongside the Joystick?
The C7950, NUCLEO-L432KC, ZLDO1117G50TA and ZSR330GTA appear in the most repositories here.
Which microcontrollers do boards using the Joystick use?
Most are built on ESP32 (3) and AVR/Arduino (2).
How big is a typical board using the Joystick?
The median is 99.5 × 90 mm, and 80% are two-layer designs.
What is the most popular open source board using the Joystick?
By GitHub stars, Iotuz esp32-hardware by CCHS-Melbourne, with 35 stars.
Can I simulate one of these boards using the Joystick before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.