16 open source boards using the CNY70
Real designs built with the CNY70, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Rc car esp32
Carlos-Santos-prog
80 × 130 mm92 parts2LMIT0AVR/Arduino
JONICA
mhechavarria
276 × 165.3 mm59 parts2LNo license0Line Sensors x8V2
Falcon-Mauricio
93 × 25 mm29 parts2LNo license0Line sensor
Technariumas
316 × 49 mm62 parts2LApache-2.00ESP32
Pastillero informativo
mollilla
63.7 × 57 mm32 parts2LNo license0Optical sensor
c4deszes
19 × 8.5 mm10 parts2LNo license0Circuito v2
mhechavarria
20.8 × 32.2 mm9 parts2LNo license0Perifericos Sensores
Pierini-Franco
99.5 × 22.3 mm23 parts2LNo license1Hps06
gzweigle
38.1 × 10.2 mm5 parts2LGPL-3.060Hps07
gzweigle
38.1 × 10.2 mm5 parts2LGPL-3.060Capteur
Darkzveller
22 × 15.5 mm4 parts2LNo license0Hps04
gzweigle
38.1 × 10.2 mm4 parts2LGPL-3.0602020-offset-4x
jkominek
45.5 × 45.3 mm5 parts2LCustom license53Hps08
gzweigle
38.1 × 10.2 mm4 parts2LGPL-3.0602040-centered-4x
jkominek
45.5 × 48 mm5 parts2LCustom license532040-centered-4x-12deg
jkominek
47 × 48 mm5 parts2LCustom license53
How designs wire the CNY70
Read from the KiCad layouts of 10 open source designs, one per repository: what each pin of the CNY70 connects to, and the resistors, capacitors and other passives placed on it.
- The A pin has a pull-up to 5V on 7 of 10 designs, most often 220 Ω (then 100 Ω).
- The K pin is tied to GND on 8 of 10 designs (a signal on 2).
- The E pin has a resistor to GND on 6 of 10 designs, most often 1 kΩ (then 20 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Apin 1 | Connected to: Signal 90% |
|
| Kpin 2 | Connected to: GND 80% · a signal 20% | — |
| Cpin 3 | Connected to: A connector 40% · 5V 40% |
|
| Epin 4 | Connected to: A connector 30% · GND 20% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Hps04 by gzweigle, 2020-offset-4x by jkominek, Perifericos Sensores by Pierini-Franco and Optical sensor by c4deszes.
The CNY70 in open source designs
The gallery holds 16 open source boards using the CNY70 from 10 GitHub repositories; a typical one measures about 45.5 × 28.6 mm and carries around 7 components.
100% are two-layer designs, the rest use four layers or more, and 38% carry an open source license.
The most starred is Hps06 by gzweigle.
Parts used alongside the CNY70
Microcontrollers on boards using the CNY70
What boards using the CNY70 are built for
CNY70: common questions
Where can I find a CNY70 reference design?
Each of the 16 boards on this page is a real design using the CNY70. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the CNY70 A pin?
The A pin has a pull-up to 5V on 7 of 10 designs, most often 220 Ω (then 100 Ω). Counted from the KiCad layouts of 10 open source designs using the CNY70.
How is the CNY70 K pin connected?
The K pin is tied to GND on 8 of 10 designs (a signal on 2). Counted from the KiCad layouts of 10 open source designs using the CNY70.
What resistor goes on the CNY70 E pin?
The E pin has a resistor to GND on 6 of 10 designs, most often 1 kΩ (then 20 kΩ). Counted from the KiCad layouts of 10 open source designs using the CNY70.
What parts are used alongside the CNY70?
The ESP32-DEVKITC, L7805 and LM358 appear in the most repositories here.
Which microcontrollers do boards using the CNY70 use?
Most are built on ESP32 (2) and AVR/Arduino (1).
How big is a typical board using the CNY70?
The median is 45.5 × 28.6 mm, and 100% are two-layer designs.
What is the most popular open source board using the CNY70?
By GitHub stars, Hps06 by gzweigle, with 60 stars.
Can I simulate one of these boards using the CNY70 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.