12 open source boards using the DRV8837DSGR
Real designs built with the DRV8837DSGR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Electronics-Design-Exploiteers-Hacker-Pager
exploiteers
108.5 × 79 mm181 parts4LCERN-OHL-S-2.027ESP32
Wristwearable
wlatif-cmyk
22.4 × 32.2 mm39 parts4LNo license8Nordic nRF
Dial me spinner main
tyevco
64 × 64 mm187 parts4LNo license0ESP32
Lune
Birkemosen
120 × 75 mm128 parts4LCC-BY-NC-4.00Nordic nRF
LightFusion
drleavsy
61 × 42 mm106 parts4LNo license0- schematic only · 39 partsSTM32
Super-8-Camera
breilly1296
39 partsNo license0 ESP32
Omni wheel
remmaTech12
91.8 × 84.9 mm58 parts2LMIT2AVR/Arduino
Malenki nano i
MarkR42
19 × 32 mm42 parts4LGPL-3.072Amod a
gallicchio
100 × 100 mm188 parts4LCERN-OHL-P-2.00AVR/Arduino
Malenki-1616
MarkR42
19 × 24.1 mm28 parts2LGPL-3.072AVR/Arduino
Malenki nanox
MarkR42
19 × 24.1 mm25 parts2LGPL-3.072- schematic only · 74 partsSTM32
Intergrated BP+
Amaza-Ronald
74 parts2LNo license0
How designs wire the DRV8837DSGR
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the DRV8837DSGR connects to, and the resistors, capacitors and other passives placed on it.
- The VM pin has a decoupling capacitor on 7 of 8 designs, most often 100 nF (then 10 µF).
- The VCC pin has a decoupling capacitor on 7 of 8 designs, most often 100 nF (then 10 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VMpin 1 | Connected to: VSYS 63% · a signal 38% |
|
| GNDpin 4, 9 | Connected to: GND 88% | — |
| SLEEPpin 7 | Connected to: The microcontroller 38%, DRV8837DSGR 25% · VCC 25% |
|
| VCCpin 8 | Connected to: 3.3V 75% · a signal 25% |
|
4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Malenki-1616 by MarkR42, Electronics-Design-Exploiteers-Hacker-Pager by exploiteers, Wristwearablepcb by wlatif-cmyk and Omni wheel by remmaTech12.
The DRV8837DSGR in open source designs
The gallery holds 12 open source boards using the DRV8837DSGR from 10 GitHub repositories; a typical one measures about 62.5 × 53 mm and carries around 66 components.
64% use four copper layers or more, and 50% carry an open source license.
The most starred is Malenki nano i by MarkR42.
Parts used alongside the DRV8837DSGR
Microcontrollers on boards using the DRV8837DSGR
What boards using the DRV8837DSGR are built for
DRV8837DSGR: common questions
Where can I find a DRV8837DSGR reference design?
Each of the 12 boards on this page is a real design using the DRV8837DSGR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the DRV8837DSGR VM pin?
The VM pin has a decoupling capacitor on 7 of 8 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 8 open source designs using the DRV8837DSGR.
What decoupling capacitors do designs use on the DRV8837DSGR VCC pin?
The VCC pin has a decoupling capacitor on 7 of 8 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 8 open source designs using the DRV8837DSGR.
What parts are used alongside the DRV8837DSGR?
The AMS1117-3.3, TPS7A2033PDBVR and USBLC6-2SC6 appear in the most repositories here.
Which microcontrollers do boards using the DRV8837DSGR use?
Most are built on ESP32 (4), AVR/Arduino (3), Nordic nRF (2) and STM32 (2).
How big is a typical board using the DRV8837DSGR?
The median is 62.5 × 53 mm, and 36% are two-layer designs.
What is the most popular open source board using the DRV8837DSGR?
By GitHub stars, Malenki nano i by MarkR42, with 72 stars.
Can I simulate one of these boards using the DRV8837DSGR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.