14 open source boards using the DRV8870DDA
Real designs built with the DRV8870DDA, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Kinisi motor controller board
szolotykh
75 × 60 mm72 parts4LMIT1DRV8870-breakout board
szolotykh
27 × 40 mm8 parts2LMIT1PRODIGY-MOTHERBOARD
mark69163
160 × 120 mm333 parts4LNo license0ESP32
Rev0
Hasatio
67.3 × 96.9 mm125 parts2LNo license0STM32
RobotBalanceador
AlexRuizDiaz
70 × 45 mm61 parts2LNo license0AVR/Arduino
Remote unit
danielmcmillan
94 × 56.3 mm47 parts2LMIT0AVR/Arduino
Helmholtz driver
UBCOrbit
114.3 × 48.3 mm23 parts4LNo license0Lesonar2 tx hardware
tornyol
47.9 × 92.3 mm58 parts2LAGPL-3.0112ESP32
RC14
AgOpenGPS-Official
145 × 108 mm88 parts2LGPL-3.020ESP32
Rev1
Hasatio
67.3 × 96.9 mm108 parts2LNo license0RP2040/RP2350
Pump board
TrendBit
90 × 100 mm181 parts4LGPL-3.00RP2040/RP2350
BDCMotorControlBoard
nunosousa
110 × 37 mm87 parts4LMIT0ESP32
SMD
Hasatio
69.2 × 55.6 mm92 parts2LNo license0LightSource
nunosousa
40 × 50 mm22 parts2LMIT0
How designs wire the DRV8870DDA
Read from the KiCad layouts of 11 open source designs, one per repository: what each pin of the DRV8870DDA connects to, and the resistors, capacitors and other passives placed on it.
- The VM pin has a decoupling capacitor on 9 of 11 designs, most often 100 nF (then 47 µF).
- The ISEN pin has a resistor to GND on 9 of 10 designs, most often 100 mΩ (then 150 mΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1, 9 | Connected to: GND 95% | — |
| VREFpin 4 | Connected to: 3.3V 73% · a signal 18% | — |
| VMpin 5 | Connected to: 12V 82% · a signal 18% |
|
| ISENpin 7 | Connected to: Signal 90% |
|
4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Lesonar2 tx hardware by tornyol, RC14 by AgOpenGPS-Official, DRV8870-breakout board by szolotykh and Kinisi motor controller board by szolotykh.
The DRV8870DDA in open source designs
The gallery holds 14 open source boards using the DRV8870DDA from 11 GitHub repositories; a typical one measures about 72.5 × 58.1 mm and carries around 80 components.
64% are two-layer designs, the rest use four layers or more, and 57% carry an open source license.
The most starred is Lesonar2 tx hardware by tornyol.
Parts used alongside the DRV8870DDA
Microcontrollers on boards using the DRV8870DDA
What boards using the DRV8870DDA are built for
DRV8870DDA: common questions
Where can I find a DRV8870DDA reference design?
Each of the 14 boards on this page is a real design using the DRV8870DDA. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the DRV8870DDA VM pin?
The VM pin has a decoupling capacitor on 9 of 11 designs, most often 100 nF (then 47 µF). Counted from the KiCad layouts of 11 open source designs using the DRV8870DDA.
What resistor goes on the DRV8870DDA ISEN pin?
The ISEN pin has a resistor to GND on 9 of 10 designs, most often 100 mΩ (then 150 mΩ). Counted from the KiCad layouts of 11 open source designs using the DRV8870DDA.
What parts are used alongside the DRV8870DDA?
The ADS1115IDGS, AMS1117-3.3, RP2040, SN74LVC1T45DBV and TPS54331DR appear in the most repositories here.
Which microcontrollers do boards using the DRV8870DDA use?
Most are built on ESP32 (4), AVR/Arduino (2), RP2040/RP2350 (2) and STM32 (2).
How big is a typical board using the DRV8870DDA?
The median is 72.5 × 58.1 mm, and 64% are two-layer designs.
What is the most popular open source board using the DRV8870DDA?
By GitHub stars, Lesonar2 tx hardware by tornyol, with 112 stars.
Can I simulate one of these boards using the DRV8870DDA before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.