11 open source boards using the DS18B20U
Real designs built with the DS18B20U, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Accumulator Board
formulaslug
127 × 91.5 mm102 parts2LNo license5Microchip SAM
EasyHive M0
jacobron
35 × 75 mm101 partsNo license4Raspberry Pi
Mothbox 5.0.4
Digital-Naturalism-Laboratories
237 × 139 mm159 parts2LMIT2Microchip SAM
Easyhive
easyhive
35 × 75 mm106 partsNo license1ESP32
Fan32-hardware
PfannenHans
63.5 × 74 mm96 parts4LCERN-OHL-P-2.00ESP32
ESP32 E-Paper-4.2 V1
filada
91 × 77 mm68 parts2LNo license0AVR/Arduino
Heater controller rev a
manhoosbilli1
47.2 × 45.8 mm62 parts2LNo license0ESP32
Esp32
Hackuarium
85 × 75 mm58 parts2LNo license0Raspberry Pi
Mothbox 5.0.6
Digital-Naturalism-Laboratories
237 × 139.1 mm159 parts2LMIT2ESP32
FunHomeLight
ZhiFun
44 × 44 mm17 parts2LMIT29Power thermistor
olin-electric-motorsports
400.9 × 174.3 mm74 parts4LMIT13
How designs wire the DS18B20U
Read from the KiCad layouts of 10 open source designs, one per repository: what each pin of the DS18B20U connects to, and the resistors, capacitors and other passives placed on it.
- The DQ pin has a pull-up to 3.3V on 7 of 10 designs, most often 4.7 kΩ.
- The VDD pin has a decoupling capacitor on 4 of 10 designs, most often 100 nF (then 100 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| DQpin 1 | Connected to: The microcontroller 60%, a connector 30% |
|
| NCpin 2, 3, 5, 6, 7 | Connected to: Not connected 100% | — |
| GNDpin 4 | Connected to: GND 70% · a signal 30% | — |
| VDDpin 8 | Connected to: 3.3V 80% · a signal 20% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include FunHomeLight by ZhiFun, Power thermistor by olin-electric-motorsports, Accumulator Board by formulaslug and EasyHive M0 by jacobron.
The DS18B20U in open source designs
The gallery holds 11 open source boards using the DS18B20U from 10 GitHub repositories; a typical one measures about 85 × 75 mm and carries around 96 components.
78% are two-layer designs, the rest use four layers or more, and 45% carry an open source license.
The most starred is FunHomeLight by ZhiFun.
Parts used alongside the DS18B20U
Microcontrollers on boards using the DS18B20U
What boards using the DS18B20U are built for
DS18B20U: common questions
Where can I find a DS18B20U reference design?
Each of the 11 boards on this page is a real design using the DS18B20U. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the DS18B20U DQ pin?
The DQ pin has a pull-up to 3.3V on 7 of 10 designs, most often 4.7 kΩ. Counted from the KiCad layouts of 10 open source designs using the DS18B20U.
What decoupling capacitors do designs use on the DS18B20U VDD pin?
The VDD pin has a decoupling capacitor on 4 of 10 designs, most often 100 nF (then 100 µF). Counted from the KiCad layouts of 10 open source designs using the DS18B20U.
What parts are used alongside the DS18B20U?
The ADS1232, ATSAMD21G, BQ2407X, TPS22919 and XC6220B331 appear in the most repositories here.
Which microcontrollers do boards using the DS18B20U use?
Most are built on ESP32 (4), Raspberry Pi (2), Microchip SAM (2) and AVR/Arduino (1).
How big is a typical board using the DS18B20U?
The median is 85 × 75 mm, and 78% are two-layer designs.
What is the most popular open source board using the DS18B20U?
By GitHub stars, FunHomeLight by ZhiFun, with 29 stars.
Can I simulate one of these boards using the DS18B20U before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.