9 open source boards using the H11AA1
Real designs built with the H11AA1, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
WCH CH32/CH55x
Fan Controller node
koko69420
100 × 100 mm51 parts2LNo license0ESP8266
Hap
AlanCarvalhoEE
46 × 77 mm33 parts2LNo license0ESP32
Xiao ac dimmer
HarryPehkonen
150 × 57 mm20 parts2LUnlicense0Bibby
austingrossman
65 × 56 mm14 parts2LCustom license0- schematic only · 86 partsESP32
Coffee
brensch
86 partsNo license0 ESP32
Esp32 dimmer
fborello-lambda
100 × 100 mm19 parts2LNo license1Prototype-2
mylife-home
87 × 68 mm32 parts2LGPL-3.00Prototype
mylife-home
88.9 × 66 mm28 parts2LGPL-3.00ESP8266
Espsense
larsimmisch
66 × 68.6 mm20 parts2LNo license0
How designs wire the H11AA1
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the H11AA1 connects to, and the resistors, capacitors and other passives placed on it.
- Pin 1 has a series resistor on 6 of 6 designs, most often 47 kΩ (then 470 kΩ).
- Pin 4 is tied to GND on 5 of 6 designs.
- Pin 6 is left unconnected on 5 of 6 designs.
- Pin 2 has a series resistor on 4 of 6 designs, most often 33 kΩ (then 43 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: Signal 100% |
|
| Pin 2 | Connected to: Signal 100% |
|
| NCpin 3 | Connected to: Not connected 100% | — |
| Pin 4 | Connected to: GND 83% · a signal 17% | — |
| Pin 5 | Connected to: A connector 50% · 3.3V 17% |
|
| Pin 6 | Connected to: Not connected 83% · a signal 17% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Esp32 dimmer by fborello-lambda, Hap by AlanCarvalhoEE, Bibby by austingrossman and Xiao ac dimmer by HarryPehkonen.
The H11AA1 in open source designs
The gallery holds 9 open source boards using the H11AA1 from 8 GitHub repositories; a typical one measures about 88 × 68.3 mm and carries around 28 components.
100% are two-layer designs, the rest use four layers or more, and 33% carry an open source license.
The most starred is Esp32 dimmer by fborello-lambda.
Parts used alongside the H11AA1
Microcontrollers on boards using the H11AA1
What boards using the H11AA1 are built for
H11AA1: common questions
Where can I find a H11AA1 reference design?
Each of the 9 boards on this page is a real design using the H11AA1. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the H11AA1 pin 1?
Pin 1 has a series resistor on 6 of 6 designs, most often 47 kΩ (then 470 kΩ). Counted from the KiCad layouts of 6 open source designs using the H11AA1.
How is the H11AA1 pin 4 connected?
Pin 4 is tied to GND on 5 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the H11AA1.
How is the H11AA1 pin 6 connected?
Pin 6 is left unconnected on 5 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the H11AA1.
Which microcontrollers do boards using the H11AA1 use?
Most are built on ESP32 (3), ESP8266 (2) and WCH CH32/CH55x (1).
How big is a typical board using the H11AA1?
The median is 88 × 68.3 mm, and 100% are two-layer designs.
What is the most popular open source board using the H11AA1?
By GitHub stars, Esp32 dimmer by fborello-lambda, with 1 stars.
Can I simulate one of these boards using the H11AA1 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.