10 open source boards using the H11L1M
Real designs built with the H11L1M, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
FunBox
GuitarML
59.7 × 67.5 mm63 parts2LMIT286ClumsyMIDI
gmcn42
65 × 56 mm21 parts2LCC-BY-SA-4.089Raspberry Pi
Mt32-pi zero breakout
wiretap-retro
65 × 30 mm13 parts2LUnlicense8ESP32
Po midi adapter
Hanz-Tech
75.3 × 71 mm51 parts2LNo license5FPGA
Courant
KrasForge
160 × 100 mm180 parts6LMIT0MomiPlug
joshnishikawa
69.9 × 69.9 mm53 parts2LNo license0ClumsyMIDI
sinitsinmike
65 × 56 mm21 parts2LCC-BY-SA-4.00FPGA
Courant.before colored actual models 20260918T190457
KrasForge
160 × 100 mm180 parts6LMIT0ESP32
Bottom
Hanz-Tech
75.3 × 71.1 mm21 parts2LNo license5Raspberry Pi
Zynthian mini
zynthian
163 × 120 mm87 parts2LNo license156
How designs wire the H11L1M
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the H11L1M connects to, and the resistors, capacitors and other passives placed on it.
- Pin 1 has a series resistor on 8 of 8 designs, most often 220 Ω.
- The VO pin has a pull-up to 3.3V on 7 of 8 designs, most often 1 kΩ (then 470 Ω).
- The VCC pin has a decoupling capacitor on 5 of 8 designs, most often 100 nF (then 22 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: Signal 100% |
|
| NCpin 3 | Connected to: Not connected 100% | — |
| VOpin 4 | Connected to: A connector 50%, 74HCT14 38% |
|
| GNDpin 5 | Connected to: GND 100% | — |
| VCCpin 6 | Connected to: 3.3V 88% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include FunBox by GuitarML, Zynthian mini by zynthian, ClumsyMIDI by gmcn42 and Mt32-pi zero breakout by wiretap-retro.
The H11L1M in open source designs
The gallery holds 10 open source boards using the H11L1M from 8 GitHub repositories; a typical one measures about 72.6 × 70.4 mm and carries around 52 components.
80% are two-layer designs, the rest use four layers or more, and 60% carry an open source license.
The most starred is FunBox by GuitarML.
Parts used alongside the H11L1M
Microcontrollers on boards using the H11L1M
What boards using the H11L1M are built for
H11L1M: common questions
Where can I find a H11L1M reference design?
Each of the 10 boards on this page is a real design using the H11L1M. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the H11L1M pin 1?
Pin 1 has a series resistor on 8 of 8 designs, most often 220 Ω. Counted from the KiCad layouts of 8 open source designs using the H11L1M.
What pull-up resistor is used on the H11L1M VO pin?
The VO pin has a pull-up to 3.3V on 7 of 8 designs, most often 1 kΩ (then 470 Ω). Counted from the KiCad layouts of 8 open source designs using the H11L1M.
What decoupling capacitors do designs use on the H11L1M VCC pin?
The VCC pin has a decoupling capacitor on 5 of 8 designs, most often 100 nF (then 22 µF). Counted from the KiCad layouts of 8 open source designs using the H11L1M.
What parts are used alongside the H11L1M?
The 74HCT14, GY-PCM5102 and SSD1306 Header appear in the most repositories here.
Which microcontrollers do boards using the H11L1M use?
Most are built on ESP32 (2), FPGA (2) and Raspberry Pi (2).
How big is a typical board using the H11L1M?
The median is 72.6 × 70.4 mm, and 80% are two-layer designs.
What is the most popular open source board using the H11L1M?
By GitHub stars, FunBox by GuitarML, with 286 stars.
Can I simulate one of these boards using the H11L1M before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.