10 open source boards using the INA181A1IDBVR
Real designs built with the INA181A1IDBVR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Mynd Main
teufelaudio
75 × 136 mm560 parts4LCC-BY-SA-4.076STM32
Mynd Main
Prototype-Fund-Hardware
75 × 136 mm560 parts4LNo license3STM32
Dcdc converter
shousei01
160 × 105 mm260 parts4LNo license0STM32
Side board
AndreiVladescu
87.5 × 50.6 mm227 parts4LCERN-OHL-S-2.00AVR/Arduino
Control Box
pauladam316
123 × 116.3 mm154 parts2LNo license0ESP32
Microohmetro uis
EDWARDPJ26
64 × 116 mm93 parts4LNo license0- schematic only · 88 partsSTM32
ReefVolt PlugControl — 2ch AC heater carrier
blueacro
88 parts4LCERN-OHL-P-2.00 RP2040/RP2350
Foc
svofski
82 × 43.5 mm39 parts2LNo license14Amod m
gallicchio
100 × 100 mm207 parts4LCERN-OHL-P-2.00Amod b
gallicchio
100 × 100 mm143 parts4LCERN-OHL-P-2.00
How designs wire the INA181A1IDBVR
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the INA181A1IDBVR connects to, and the resistors, capacitors and other passives placed on it.
- The V+ pin has a decoupling capacitor on 7 of 8 designs, most often 100 nF.
- The REF pin has a resistor to GND on 6 of 8 designs, most often 16 kΩ (then 1 kΩ).
- The OUT_1 pin has a series resistor on 5 of 8 designs, most often 10 kΩ (then 1 kΩ).
- The + pin has a series resistor on 5 of 8 designs, most often 10 Ω (then 33 mΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| OUT_1pin 1 | Connected to: The microcontroller 25% |
|
| GNDpin 2 | Connected to: GND 100% | — |
| +pin 3 | Connected to: Signal 63% · 6V 25% |
|
| -pin 4 | Connected to: Signal 75% |
|
| REFpin 5 | Connected to: The microcontroller 25% · GND 25% |
|
| V+pin 6 | Connected to: 3.3V 100% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Mynd Main by teufelaudio, Foc by svofski, Mynd Main by Prototype-Fund-Hardware and Side board by AndreiVladescu.
The INA181A1IDBVR in open source designs
The gallery holds 10 open source boards using the INA181A1IDBVR from 9 GitHub repositories; a typical one measures about 87.5 × 105 mm and carries around 181 components.
80% use four copper layers or more, and 50% carry an open source license.
The most starred is Mynd Main by teufelaudio.
Parts used alongside the INA181A1IDBVR
Microcontrollers on boards using the INA181A1IDBVR
What boards using the INA181A1IDBVR are built for
INA181A1IDBVR: common questions
Where can I find a INA181A1IDBVR reference design?
Each of the 10 boards on this page is a real design using the INA181A1IDBVR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the INA181A1IDBVR V+ pin?
The V+ pin has a decoupling capacitor on 7 of 8 designs, most often 100 nF. Counted from the KiCad layouts of 8 open source designs using the INA181A1IDBVR.
What resistor goes on the INA181A1IDBVR REF pin?
The REF pin has a resistor to GND on 6 of 8 designs, most often 16 kΩ (then 1 kΩ). Counted from the KiCad layouts of 8 open source designs using the INA181A1IDBVR.
What resistor goes on the INA181A1IDBVR OUT_1 pin?
The OUT_1 pin has a series resistor on 5 of 8 designs, most often 10 kΩ (then 1 kΩ). Counted from the KiCad layouts of 8 open source designs using the INA181A1IDBVR.
What parts are used alongside the INA181A1IDBVR?
The BQ25713RSNR, FT24C512A-TSR-T, LM51231QRGRRQ1, PTPS25751SRSMR and SGM358YMS appear in the most repositories here.
Which microcontrollers do boards using the INA181A1IDBVR use?
Most are built on STM32 (5), AVR/Arduino (1), ESP32 (1) and RP2040/RP2350 (1).
How big is a typical board using the INA181A1IDBVR?
The median is 87.5 × 105 mm, and 20% are two-layer designs.
What is the most popular open source board using the INA181A1IDBVR?
By GitHub stars, Mynd Main by teufelaudio, with 76 stars.
Can I simulate one of these boards using the INA181A1IDBVR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.