5 open source boards using the LM3914

Real designs built with the LM3914, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

5 boardsClear filters|Most starred

How designs wire the LM3914

Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the LM3914 connects to, and the resistors, capacitors and other passives placed on it.

  • Pin 8 has a series resistor on 4 of 5 designs, most often 4.7 kΩ (then 2.7 kΩ).
  • Pin 3 has a capacitor to GND on 3 of 5 designs, most often 22 µF (then 4.7 µF).
  • Pin 2 is tied to GND on 3 of 5 designs (a signal on 2).
  • Pin 2 has a series resistor on 2 of 5 designs, most often 4.7 kΩ.
Pin 2Connected to: GND 60% · a signal 40%
  • Series resistor on 40% · 4.7 kΩ (2)
Pin 3Connected to: MT3608 40%, TP4056 40%, a connector 40% · 9V 40%
  • Capacitor to GND on 60% · 22 µF (2), 4.7 µF (1)
  • Series resistor on 40% · 4.7 kΩ (2), 100 kΩ (2)
  • Inductor on 40% · 22 µH (2)
Pin 4Connected to: Signal 60% · GND 40%
  • Series resistor on 40% · 4.7 kΩ (2)
Pin 6Connected to: Signal 100%
  • Series resistor on 40% · 2.7 kΩ (1), 130 kΩ (1)
Pin 7Connected to: Signal 100%
  • Series resistor on 40% · 2.7 kΩ (1), 130 kΩ (1)
Pin 8Connected to: Signal 80% · GND 20%
  • Series resistor on 80% · 4.7 kΩ (2), 2.7 kΩ (1), 130 kΩ (1)
  • Resistor to GND on 40% · 8.2 kΩ (1), 4.87 kΩ (1)
Pin 9Connected to: A connector 60%, MT3608 40%, TP4056 40% · not connected 20% · GND 20%
  • Series resistor on 40% · 4.7 kΩ (2), 100 kΩ (2)
  • Capacitor to GND on 40% · 22 µF (2)
  • Inductor on 40% · 22 µH (2)

11 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include OTTOtact by cester-ino, OTTOtact by cester-ino, Battery tester by nrth3rnlb and Compressor front by UTS-500-Series.

The LM3914 in open source designs

The gallery holds 5 open source boards using the LM3914 from 5 GitHub repositories; a typical one measures about 103.4 × 110 mm and carries around 104 components.

100% are two-layer designs, the rest use four layers or more, and 100% carry an open source license.

The most starred is OTTOtact by cester-ino.

Microcontrollers on boards using the LM3914

What boards using the LM3914 are built for

LM3914: common questions

Where can I find a LM3914 reference design?

Each of the 5 boards on this page is a real design using the LM3914. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What resistor goes on the LM3914 pin 8?

Pin 8 has a series resistor on 4 of 5 designs, most often 4.7 kΩ (then 2.7 kΩ). Counted from the KiCad layouts of 5 open source designs using the LM3914.

How is the LM3914 pin 3 connected?

Pin 3 has a capacitor to GND on 3 of 5 designs, most often 22 µF (then 4.7 µF). Counted from the KiCad layouts of 5 open source designs using the LM3914.

How is the LM3914 pin 2 connected?

Pin 2 is tied to GND on 3 of 5 designs (a signal on 2). Counted from the KiCad layouts of 5 open source designs using the LM3914.

What parts are used alongside the LM3914?

The 74HC125, ATmega32U4-AU, FS312F-G, MCP602 and MT3608 appear in the most repositories here.

Which microcontrollers do boards using the LM3914 use?

Most are built on AVR/Arduino (2).

How big is a typical board using the LM3914?

The median is 103.4 × 110 mm, and 100% are two-layer designs.

What is the most popular open source board using the LM3914?

By GitHub stars, OTTOtact by cester-ino, with 49 stars.

Can I simulate one of these boards using the LM3914 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part