6 open source boards using the LMR51635YDDCR

Real designs built with the LMR51635YDDCR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

6 boardsClear filters|Most starred

How designs wire the LMR51635YDDCR

Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the LMR51635YDDCR connects to, and the resistors, capacitors and other passives placed on it.

  • The FB_1 pin has a resistor to GND on 6 of 6 designs, most often 19.1 kΩ (then 20 kΩ).
  • The VIN_3 pin has a decoupling capacitor on 6 of 6 designs, most often 100 nF (then 4.7 µF).
  • The SW_5 pin has a series capacitor on 6 of 6 designs, most often 100 nF.
  • The SW_5 pin has a inductor on 6 of 6 designs, most often 3.3 µH (then 10 µH).
FB_1pin 1Connected to: Signal 100%
  • Resistor to GND on 100% · 19.1 kΩ (2), 20 kΩ (2), 8.87 kΩ (1)
  • Pull-up to 5V on 50% · 100 kΩ (2), 120 kΩ (1)
  • Series resistor on 50% · 100 kΩ (3)
VIN_3pin 3Connected to: VIN 100%
  • Decoupling capacitor on 100% · 100 nF (5), 4.7 µF (3), 1 µF (3)
GND_4pin 4Connected to: GND 100%
SW_5pin 5Connected to: Signal 100%
  • Series capacitor on 100% · 100 nF (6)
  • Inductor on 100% · 3.3 µH (2), 10 µH (2), 8.2 µH (1)
CB_6pin 6Connected to: Signal 100%
  • Series capacitor on 100% · 100 nF (6)

1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include OpenFC-Lite by OpenDrone-hw, URC by spikonado, Smu main by PaulBichl and Bay node by kartben.

The LMR51635YDDCR in open source designs

The gallery holds 6 open source boards using the LMR51635YDDCR from 6 GitHub repositories; a typical one measures about 78.1 × 78 mm and carries around 97 components.

83% use four copper layers or more, and 50% carry an open source license.

The most starred is OpenFC-Lite by OpenDrone-hw.

Microcontrollers on boards using the LMR51635YDDCR

LMR51635YDDCR: common questions

Where can I find a LMR51635YDDCR reference design?

Each of the 6 boards on this page is a real design using the LMR51635YDDCR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What resistor goes on the LMR51635YDDCR FB_1 pin?

The FB_1 pin has a resistor to GND on 6 of 6 designs, most often 19.1 kΩ (then 20 kΩ). Counted from the KiCad layouts of 6 open source designs using the LMR51635YDDCR.

What decoupling capacitors do designs use on the LMR51635YDDCR VIN_3 pin?

The VIN_3 pin has a decoupling capacitor on 6 of 6 designs, most often 100 nF (then 4.7 µF). Counted from the KiCad layouts of 6 open source designs using the LMR51635YDDCR.

How is the LMR51635YDDCR SW_5 pin connected?

The SW_5 pin has a series capacitor on 6 of 6 designs, most often 100 nF. Counted from the KiCad layouts of 6 open source designs using the LMR51635YDDCR.

What parts are used alongside the LMR51635YDDCR?

The USBLC6-2SC6, AP2112K-3.3TRG1, ESP32-S3-MINI-1-N8 and STUSB4500QTR appear in the most repositories here.

Which microcontrollers do boards using the LMR51635YDDCR use?

Most are built on ESP32 (3), RP2040/RP2350 (1) and STM32 (1).

How big is a typical board using the LMR51635YDDCR?

The median is 78.1 × 78 mm, and 17% are two-layer designs.

What is the most popular open source board using the LMR51635YDDCR?

By GitHub stars, OpenFC-Lite by OpenDrone-hw, with 32 stars.

Can I simulate one of these boards using the LMR51635YDDCR before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part