6 open source boards using the LTV-817S-TA1
Real designs built with the LTV-817S-TA1, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Dc dc 250w tl494
picli3
138 × 65.5 mm48 parts2LNo license1Raspberry Pi
Manafish Mainboard
Tropaion
70 × 109.2 mm123 parts4LAGPL-3.00DishyPi1
jrseti
94.6 × 69.3 mm102 parts4LMIT0DishyPi1
jrseti
94.6 × 69.3 mm102 parts4LMIT0STM32
Mcu test board
jrseti
59.9 × 57.5 mm57 parts4LMIT0AVR/Arduino
BMS Sensor
weaslepalace
80 × 30 mm44 parts2LNo license0
How designs wire the LTV-817S-TA1
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the LTV-817S-TA1 connects to, and the resistors, capacitors and other passives placed on it.
- The 1 pin has a series resistor on 3 of 5 designs, most often 1 kΩ (then 100 Ω).
- The 3 pin is tied to GND on 3 of 5 designs (a signal on 2).
- The 3 pin has a resistor to GND on 2 of 5 designs, most often 1 kΩ (then 10 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| 1pin 1 | Connected to: Signal 100% |
|
| 3pin 3 | Connected to: GND 60% · a signal 40% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Dc dc 250w tl494 by picli3, DishyPi1 by jrseti, DishyPi1 by jrseti and Manafish Mainboard by Tropaion.
The LTV-817S-TA1 in open source designs
The gallery holds 6 open source boards using the LTV-817S-TA1 from 5 GitHub repositories; a typical one measures about 87.3 × 67.4 mm and carries around 80 components.
67% use four copper layers or more, and 67% carry an open source license.
The most starred is Dc dc 250w tl494 by picli3.
Parts used alongside the LTV-817S-TA1
Microcontrollers on boards using the LTV-817S-TA1
What boards using the LTV-817S-TA1 are built for
LTV-817S-TA1: common questions
Where can I find a LTV-817S-TA1 reference design?
Each of the 6 boards on this page is a real design using the LTV-817S-TA1. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the LTV-817S-TA1 1 pin?
The 1 pin has a series resistor on 3 of 5 designs, most often 1 kΩ (then 100 Ω). Counted from the KiCad layouts of 5 open source designs using the LTV-817S-TA1.
How is the LTV-817S-TA1 3 pin connected?
The 3 pin is tied to GND on 3 of 5 designs (a signal on 2). Counted from the KiCad layouts of 5 open source designs using the LTV-817S-TA1.
What parts are used alongside the LTV-817S-TA1?
The CAT24C256WI-GT3, ISO1540DR, LM75BIMX-5/NOPB, LTC4311ISC6#TRPBF and LTV-827S-TA1 appear in the most repositories here.
Which microcontrollers do boards using the LTV-817S-TA1 use?
Most are built on AVR/Arduino (1), Raspberry Pi (1) and STM32 (1).
How big is a typical board using the LTV-817S-TA1?
The median is 87.3 × 67.4 mm, and 33% are two-layer designs.
What is the most popular open source board using the LTV-817S-TA1?
By GitHub stars, Dc dc 250w tl494 by picli3, with 1 stars.
Can I simulate one of these boards using the LTV-817S-TA1 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.