6 open source boards using the CAT24C256WI-GT3

Real designs built with the CAT24C256WI-GT3, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

6 boardsClear filters|Most starred

How designs wire the CAT24C256WI-GT3

Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the CAT24C256WI-GT3 connects to, and the resistors, capacitors and other passives placed on it.

  • The SDA pin has a pull-up to 3.3V on 6 of 6 designs, most often 3.9 kΩ (then 4.7 kΩ).
  • The SCL pin has a pull-up to 3.3V on 6 of 6 designs, most often 3.9 kΩ (then 4.7 kΩ).
  • The A1 pin is tied to GND on 6 of 6 designs.
  • The A2 pin is tied to GND on 6 of 6 designs.
A0pin 1Connected to: GND 83% · a signal 17%
A1pin 2Connected to: GND 100%
A2pin 3Connected to: GND 100%
VSSpin 4Connected to: GND 100%
SDApin 5Connected to: A connector 67%, the microcontroller 33%
  • Pull-up to 3.3V on 100% · 3.9 kΩ (3), 4.7 kΩ (2), 5.1 kΩ (1)
SCLpin 6Connected to: A connector 67%, the microcontroller 33%
  • Pull-up to 3.3V on 100% · 3.9 kΩ (3), 4.7 kΩ (2), 5.1 kΩ (1)
VCCpin 8Connected to: 3.3V 100%
  • Decoupling capacitor on 83% · 100 nF (5)

1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Ultimate Hacking Keyboard - Right Main Board by UltimateHackingKeyboard, UHK 60 v2 - Right Half by UltimateHackingKeyboard, Pi hat by race-on and Lora daq module by danielkm-ee.

The CAT24C256WI-GT3 in open source designs

The gallery holds 6 open source boards using the CAT24C256WI-GT3 from 6 GitHub repositories; a typical one measures about 94.6 × 69.3 mm and carries around 102 components.

50% are two-layer designs, the rest use four layers or more, and 67% carry an open source license.

The most starred is Ultimate Hacking Keyboard - Right Main Board by UltimateHackingKeyboard.

Microcontrollers on boards using the CAT24C256WI-GT3

What boards using the CAT24C256WI-GT3 are built for

CAT24C256WI-GT3: common questions

Where can I find a CAT24C256WI-GT3 reference design?

Each of the 6 boards on this page is a real design using the CAT24C256WI-GT3. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What pull-up resistor is used on the CAT24C256WI-GT3 SDA pin?

The SDA pin has a pull-up to 3.3V on 6 of 6 designs, most often 3.9 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 6 open source designs using the CAT24C256WI-GT3.

What pull-up resistor is used on the CAT24C256WI-GT3 SCL pin?

The SCL pin has a pull-up to 3.3V on 6 of 6 designs, most often 3.9 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 6 open source designs using the CAT24C256WI-GT3.

How is the CAT24C256WI-GT3 A1 pin connected?

The A1 pin is tied to GND on 6 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the CAT24C256WI-GT3.

What parts are used alongside the CAT24C256WI-GT3?

The ESD, ISO1540DR, LM75BIMX-5/NOPB, LTC4311ISC6#TRPBF and LTV-817S-TA1 appear in the most repositories here.

Which microcontrollers do boards using the CAT24C256WI-GT3 use?

Most are built on NXP (2).

How big is a typical board using the CAT24C256WI-GT3?

The median is 94.6 × 69.3 mm, and 50% are two-layer designs.

What is the most popular open source board using the CAT24C256WI-GT3?

By GitHub stars, Ultimate Hacking Keyboard - Right Main Board by UltimateHackingKeyboard, with 177 stars.

Can I simulate one of these boards using the CAT24C256WI-GT3 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part