25 open source boards using the LTV-847S

Real designs built with the LTV-847S, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

25 boardsClear filters|Most starred

How designs wire the LTV-847S

Read from the KiCad layouts of 10 open source designs, one per repository: what each pin of the LTV-847S connects to, and the resistors, capacitors and other passives placed on it.

  • The EM4 pin is tied to GND on 8 of 9 designs.
  • The EM3 pin is tied to GND on 8 of 9 designs.
  • The EM2 pin is tied to GND on 8 of 9 designs.
  • The EM1 pin is tied to GND on 8 of 9 designs.
AN1pin 1Connected to: Signal 90%
  • Series resistor on 50% · 330 Ω (2), 10 kΩ (1), 240 Ω (1)
AN2pin 3Connected to: Signal 80% · 5V 20%
  • Series resistor on 50% · 330 Ω (2), 10 kΩ (1), 240 Ω (1)
AN3pin 5Connected to: Signal 80%
  • Series resistor on 50% · 330 Ω (2), 10 kΩ (1), 240 Ω (1)
CAT3pin 6Connected to: A connector 40%, LTV-847S 20% · GND 30%
  • Series resistor on 30% · 120 Ω (1), 1 kΩ (1), 10 kΩ (1)
AN4pin 7Connected to: Signal 80%
  • Series resistor on 50% · 330 Ω (2), 10 kΩ (1), 120 Ω (1)
  • Capacitor to GND on 30% · 100 pF (2), 100 nF (1)
EM4pin 9Connected to: GND 89%
EM3pin 11Connected to: GND 89%
EM2pin 13Connected to: GND 89%
EM1pin 15Connected to: GND 89%

7 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include PiGarage by bryce-builds, 328 3ch can devboard by HKUST-Red-Bird-Racing-EVRT, Before e6961eff764b14fa by JCastel358 and AEM-60DC8 V1.2 by akhemka-cmd.

The LTV-847S in open source designs

The gallery holds 25 open source boards using the LTV-847S from 10 GitHub repositories; a typical one measures about 86 × 145 mm and carries around 197 components.

64% use four copper layers or more, and 20% carry an open source license.

The most starred is PiGarage by bryce-builds.

Microcontrollers on boards using the LTV-847S

LTV-847S: common questions

Where can I find a LTV-847S reference design?

Each of the 25 boards on this page is a real design using the LTV-847S. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the LTV-847S EM4 pin connected?

The EM4 pin is tied to GND on 8 of 9 designs. Counted from the KiCad layouts of 10 open source designs using the LTV-847S.

How is the LTV-847S EM3 pin connected?

The EM3 pin is tied to GND on 8 of 9 designs. Counted from the KiCad layouts of 10 open source designs using the LTV-847S.

How is the LTV-847S EM2 pin connected?

The EM2 pin is tied to GND on 8 of 9 designs. Counted from the KiCad layouts of 10 open source designs using the LTV-847S.

What parts are used alongside the LTV-847S?

The ISO1540DR, 40106, AP2112K-3.3TRG1, ATMEGA328-A and CAT24C256WI-GT3 appear in the most repositories here.

Which microcontrollers do boards using the LTV-847S use?

Most are built on AVR/Arduino (4), STM32 (3), NXP (2) and RP2040/RP2350 (1).

How big is a typical board using the LTV-847S?

The median is 86 × 145 mm, and 36% are two-layer designs.

What is the most popular open source board using the LTV-847S?

By GitHub stars, PiGarage by bryce-builds, with 8 stars.

Can I simulate one of these boards using the LTV-847S before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part