7 open source boards using the LTV-817S-TA1-C
Real designs built with the LTV-817S-TA1-C, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
FE UFPR 4 0
josearistidesbail
159.6 × 130 mm313 parts4LNo license0ESP32
ESP-relay-6ch
koson
173 × 67.8 mm109 parts2LNo license0Ulva
ivere27
100 × 100 mm98 parts2LMIT0ESP32
ESP 8 Relay Module
thermseekr
148 × 67.8 mm271 parts2LCC-BY-NC-4.06Raspberry Pi
Raspberry Pi Pico Logger - Relay
WestianPKl
100.5 × 83 mm77 parts2LNo license0Raspberry Pi
Raspberry Pi Pico Logger - Relay
WestianPKl
100.5 × 83 mm77 parts2LNo license0IN-24V
Thierry-oshw
10 × 50.8 mm6 parts2LCERN-OHL-P-2.00
How designs wire the LTV-817S-TA1-C
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the LTV-817S-TA1-C connects to, and the resistors, capacitors and other passives placed on it.
- Pin 1 has a series resistor on 5 of 7 designs, most often 2.2 kΩ (then 10 kΩ).
- Pin 2 is tied to GND on 5 of 7 designs (a signal on 2).
- Pin 3 has a series resistor on 3 of 7 designs, most often 680 Ω (then 47 kΩ).
- Pin 4 has a pull-up to 3.3V on 3 of 7 designs, most often 3.3 kΩ (then 10 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: Signal 100% |
|
| Pin 2 | Connected to: GND 71% · a signal 29% | — |
| Pin 3 | Connected to: Signal 57% · GND 43% |
|
| Pin 4 | Connected to: The microcontroller 57%, LTV-817S-TA1-C 29%, a connector 29% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include ESP 8 Relay Module by thermseekr, Ulva by ivere27, FE UFPR 4 0 by josearistidesbail and ESP-relay-6ch by koson.
The LTV-817S-TA1-C in open source designs
The gallery holds 7 open source boards using the LTV-817S-TA1-C from 7 GitHub repositories; a typical one measures about 100.5 × 83 mm and carries around 98 components.
86% are two-layer designs, the rest use four layers or more, and 29% carry an open source license.
The most starred is ESP 8 Relay Module by thermseekr.
Parts used alongside the LTV-817S-TA1-C
Microcontrollers on boards using the LTV-817S-TA1-C
What boards using the LTV-817S-TA1-C are built for
LTV-817S-TA1-C: common questions
Where can I find a LTV-817S-TA1-C reference design?
Each of the 7 boards on this page is a real design using the LTV-817S-TA1-C. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the LTV-817S-TA1-C pin 1?
Pin 1 has a series resistor on 5 of 7 designs, most often 2.2 kΩ (then 10 kΩ). Counted from the KiCad layouts of 7 open source designs using the LTV-817S-TA1-C.
How is the LTV-817S-TA1-C pin 2 connected?
Pin 2 is tied to GND on 5 of 7 designs (a signal on 2). Counted from the KiCad layouts of 7 open source designs using the LTV-817S-TA1-C.
What resistor goes on the LTV-817S-TA1-C pin 3?
Pin 3 has a series resistor on 3 of 7 designs, most often 680 Ω (then 47 kΩ). Counted from the KiCad layouts of 7 open source designs using the LTV-817S-TA1-C.
Which microcontrollers do boards using the LTV-817S-TA1-C use?
Most are built on ESP32 (2) and Raspberry Pi (2).
How big is a typical board using the LTV-817S-TA1-C?
The median is 100.5 × 83 mm, and 86% are two-layer designs.
What is the most popular open source board using the LTV-817S-TA1-C?
By GitHub stars, ESP 8 Relay Module by thermseekr, with 6 stars.
Can I simulate one of these boards using the LTV-817S-TA1-C before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.