10 open source boards using the MC33063AD
Real designs built with the MC33063AD, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
PIC
YAPSCO-10V
simonjoh
82.8 × 73.2 mm72 parts2LGPL-3.07STM32
MidiBox3
Dethernal
100 × 100 mm114 parts2LMIT5FPGA
Xc17 prom prog
msinger
123 × 95 mm281 parts2LCC-BY-SA-4.03ESP32
DA Sensorbox
Lelk0e
87.2 × 71.3 mm80 parts2LNo license0ESP32
Weather station project
laith73
95 × 75 mm78 parts4LMIT0AVR/Arduino
Uvw switch
MIH-pi
139.7 × 76.2 mm61 parts4LMIT0AVR/Arduino
Pev uvw sw
mit-pev
139.7 × 76.2 mm61 parts4LNo license0Voltage Regulator seneryo Y (Input 3.7V)
manyetox
50 × 50 mm43 parts2LNo license0STM32
MidiBox3 b
Dethernal
100 × 100 mm105 parts2LMIT5Lab2 psu
Lavapeeble
48.1 × 48 mm24 parts2LNo license0
How designs wire the MC33063AD
Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the MC33063AD connects to, and the resistors, capacitors and other passives placed on it.
- The IPK pin has a pull-up to 12V on 9 of 9 designs, most often 1 Ω (then 120 mΩ).
- The TC pin has a capacitor to GND on 8 of 9 designs, most often 470 pF (then 1.5 nF).
- The VFB pin has a resistor to GND on 7 of 9 designs, most often 1.1 kΩ (then 8.6 kΩ).
- The VFB pin has a pull-up to 3.3V on 6 of 9 designs, most often 20 kΩ (then 1 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| SWCpin 1 | Connected to: Signal 100% |
|
| SWEpin 2 | Connected to: Signal 67% · GND 33% |
|
| TCpin 3 | Connected to: Signal 100% |
|
| GNDpin 4 | Connected to: GND 89% | — |
| VFBpin 5 | Connected to: Signal 100% |
|
| VINpin 6 | Connected to: 12V 100% |
|
| IPKpin 7 | Connected to: Signal 100% |
|
| DCpin 8 | Connected to: Signal 100% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include YAPSCO-10V by simonjoh, MidiBox3 by Dethernal, Xc17 prom prog by msinger and Weather station project by laith73.
The MC33063AD in open source designs
The gallery holds 10 open source boards using the MC33063AD from 9 GitHub repositories; a typical one measures about 97.5 × 75.6 mm and carries around 75 components.
70% are two-layer designs, the rest use four layers or more, and 60% carry an open source license.
The most starred is YAPSCO-10V by simonjoh.
Parts used alongside the MC33063AD
Microcontrollers on boards using the MC33063AD
What boards using the MC33063AD are built for
MC33063AD: common questions
Where can I find a MC33063AD reference design?
Each of the 10 boards on this page is a real design using the MC33063AD. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the MC33063AD IPK pin?
The IPK pin has a pull-up to 12V on 9 of 9 designs, most often 1 Ω (then 120 mΩ). Counted from the KiCad layouts of 9 open source designs using the MC33063AD.
How is the MC33063AD TC pin connected?
The TC pin has a capacitor to GND on 8 of 9 designs, most often 470 pF (then 1.5 nF). Counted from the KiCad layouts of 9 open source designs using the MC33063AD.
What resistor goes on the MC33063AD VFB pin?
The VFB pin has a resistor to GND on 7 of 9 designs, most often 1.1 kΩ (then 8.6 kΩ). Counted from the KiCad layouts of 9 open source designs using the MC33063AD.
What parts are used alongside the MC33063AD?
The ATMEGA328P-AU, BME280, M453_LQFP48 and TCAN1042V-Q1 appear in the most repositories here.
Which microcontrollers do boards using the MC33063AD use?
Most are built on AVR/Arduino (2), ESP32 (2), STM32 (2) and FPGA (1).
How big is a typical board using the MC33063AD?
The median is 97.5 × 75.6 mm, and 70% are two-layer designs.
What is the most popular open source board using the MC33063AD?
By GitHub stars, YAPSCO-10V by simonjoh, with 7 stars.
Can I simulate one of these boards using the MC33063AD before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.