20 open source boards using the MCP6002T-I/SN

Real designs built with the MCP6002T-I/SN, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

20 boardsClear filters|Most starred

How designs wire the MCP6002T-I/SN

Read from the KiCad layouts of 12 open source designs, one per repository: what each pin of the MCP6002T-I/SN connects to, and the resistors, capacitors and other passives placed on it.

  • The V- pin is tied to GND on 11 of 12 designs.
  • The - pins have a series resistor on 8 of 12 designs, most often 10 kΩ (then 220 Ω).
  • The V+ pin has a decoupling capacitor on 8 of 12 designs, most often 100 nF (then 4.7 µF).
  • The OUTA_1 pin has a series resistor on 7 of 12 designs, most often 10 kΩ (then 2 MΩ).
OUTA_1pin 1Connected to: Signal 92%
  • Series resistor on 58% · 10 kΩ (4), 2 MΩ (1), 1 MΩ (1)
-pin 2, 6Connected to: Signal 83%
  • Series resistor on 67% · 10 kΩ (8), 220 Ω (2), 20 kΩ (2)
+pin 3, 5Connected to: Signal 71%
  • Series resistor on 58% · 10 kΩ (8), 1 MΩ (3), 100 Ω (2)
  • Resistor to GND on 42% · 10 kΩ (4), 100 kΩ (1)
  • Pull-up to 5V on 33% · 10 kΩ (2), 100 kΩ (1)
V-pin 4Connected to: GND 92%
OUTB_7pin 7Connected to: Signal 67% · not connected 17% · VREF_0_7_OUT 17%
  • Series resistor on 33% · 10 kΩ (2), 2 kΩ (1), 1 kΩ (1)
V+pin 8Connected to: 5V 75% · a signal 17%
  • Decoupling capacitor on 67% · 100 nF (6), 4.7 µF (1), 220 µF (1)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include OpenThereminV4 by GaudiLabs, GuitarPedalSTM32 by GuitarML, Base by bread-modular and Lambda x2 by rusefi.

The MCP6002T-I/SN in open source designs

The gallery holds 20 open source boards using the MCP6002T-I/SN from 12 GitHub repositories; a typical one measures about 85.9 × 87.5 mm and carries around 154 components.

55% use four copper layers or more, and 60% carry an open source license.

The most starred is OpenThereminV4 by GaudiLabs.

Parts used alongside the MCP6002T-I/SN

Microcontrollers on boards using the MCP6002T-I/SN

MCP6002T-I/SN: common questions

Where can I find a MCP6002T-I/SN reference design?

Each of the 20 boards on this page is a real design using the MCP6002T-I/SN. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the MCP6002T-I/SN V- pin connected?

The V- pin is tied to GND on 11 of 12 designs. Counted from the KiCad layouts of 12 open source designs using the MCP6002T-I/SN.

What resistor goes on the MCP6002T-I/SN - pin?

The - pins have a series resistor on 8 of 12 designs, most often 10 kΩ (then 220 Ω). Counted from the KiCad layouts of 12 open source designs using the MCP6002T-I/SN.

What decoupling capacitors do designs use on the MCP6002T-I/SN V+ pin?

The V+ pin has a decoupling capacitor on 8 of 12 designs, most often 100 nF (then 4.7 µF). Counted from the KiCad layouts of 12 open source designs using the MCP6002T-I/SN.

Which microcontrollers do boards using the MCP6002T-I/SN use?

Most are built on STM32 (6), ESP32 (3), Nordic nRF (3) and AVR/Arduino (2).

How big is a typical board using the MCP6002T-I/SN?

The median is 85.9 × 87.5 mm, and 45% are two-layer designs.

What is the most popular open source board using the MCP6002T-I/SN?

By GitHub stars, OpenThereminV4 by GaudiLabs, with 238 stars.

Can I simulate one of these boards using the MCP6002T-I/SN before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part