14 open source boards using the TLC272
Real designs built with the TLC272, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Sonus7 rev1
BasementCircuits
200 × 87.8 mm257 parts2LCERN-OHL-W-2.06AVR/Arduino
Opamp vu meter
CASE-Association
92.5 × 99.7 mm42 parts2LGPL-3.03Ultraschallsensor
Tinkerforge
49.5 × 38.1 mm64 parts2LNo license2Microchip SAM
Ascom flat panel
letelescope
56.5 × 74 mm14 parts2LMIT2STM32
Electronicload
GM4AJK
54.5 × 80 mm62 parts4LNo license1Raspberry Pi
Motherboard
BryggansBryggeri
85 × 56.5 mm29 parts2LNo license1AVR/Arduino
Hauptplatine
JoshCrouch
220 × 160.5 mm504 parts4LNo license0AVR/Arduino
H9ps
c3h9dx
70 × 60 mm69 parts2LNo license0Pulsometer
Matii178
63.3 × 40.4 mm31 parts2LNo license0Td rgbinput
tdaede
165 × 50 mm116 parts2LNo license370Schaltplan Ultraschallsensor
Tinkerforge
43.5 × 46.9 mm54 parts2LNo license2Raspberry Pi
Motherboard org
BryggansBryggeri
60.2 × 88.8 mm29 parts2LNo license1ESP32
VCU
matatma23-gento
60.5 × 100.5 mm160 parts4LNo license0Input stage
BasementCircuits
45 × 85 mm17 parts2LCERN-OHL-W-2.06
How designs wire the TLC272
Read from the KiCad layouts of 11 open source designs, one per repository: what each pin of the TLC272 connects to, and the resistors, capacitors and other passives placed on it.
- The - pins have a series resistor on 9 of 11 designs, most often 1 kΩ (then 100 kΩ).
- Pin 7 has a series resistor on 9 of 11 designs, most often 20 kΩ (then 10 Ω).
- Pin 1 has a series resistor on 8 of 11 designs, most often 10 Ω (then 100 kΩ).
- The V- pin is tied to GND on 8 of 11 designs (a signal on 2).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: Signal 91% |
|
| -pin 2, 6 | Connected to: Signal 91% |
|
| +pin 3, 5 | Connected to: Signal 91% |
|
| V-pin 4 | Connected to: GND 73% · a signal 18% | — |
| Pin 7 | Connected to: Signal 91% |
|
| V+pin 8 | Connected to: 5V 91% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Td rgbinput by tdaede, Input stage by BasementCircuits, Opamp vu meter by CASE-Association and Ascom flat panel by letelescope.
The TLC272 in open source designs
The gallery holds 14 open source boards using the TLC272 from 11 GitHub repositories; a typical one measures about 61.9 × 77 mm and carries around 58 components.
79% are two-layer designs, the rest use four layers or more, and 29% carry an open source license.
The most starred is Td rgbinput by tdaede.
Parts used alongside the TLC272
Microcontrollers on boards using the TLC272
What boards using the TLC272 are built for
TLC272: common questions
Where can I find a TLC272 reference design?
Each of the 14 boards on this page is a real design using the TLC272. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the TLC272 - pin?
The - pins have a series resistor on 9 of 11 designs, most often 1 kΩ (then 100 kΩ). Counted from the KiCad layouts of 11 open source designs using the TLC272.
What resistor goes on the TLC272 pin 7?
Pin 7 has a series resistor on 9 of 11 designs, most often 20 kΩ (then 10 Ω). Counted from the KiCad layouts of 11 open source designs using the TLC272.
What resistor goes on the TLC272 pin 1?
Pin 1 has a series resistor on 8 of 11 designs, most often 10 Ω (then 100 kΩ). Counted from the KiCad layouts of 11 open source designs using the TLC272.
Which microcontrollers do boards using the TLC272 use?
Most are built on AVR/Arduino (3), Raspberry Pi (2), ESP32 (1) and Microchip SAM (1).
How big is a typical board using the TLC272?
The median is 61.9 × 77 mm, and 79% are two-layer designs.
What is the most popular open source board using the TLC272?
By GitHub stars, Td rgbinput by tdaede, with 370 stars.
Can I simulate one of these boards using the TLC272 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.