7 open source boards using the TLC59108xPW
Real designs built with the TLC59108xPW, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Isoblue
oats-center
115 × 78 mm114 parts4LMIT25ESP32
QPocketPCR Main
GaudiLabs
82.5 × 140 mm96 parts2LGPL-3.021PingBoard
PingTechGmbH
87.6 × 25.4 mm23 parts2LMIT3PIC
IOT F26 PROJ
kaballian
65 × 30 mm60 parts4LNo license1STM32
Spha btnn hardware
sillevl
37.6 × 37.6 mm68 parts4LNo license0STM32
Spha btnu hardware
sillevl
29 × 29 mm47 parts4LNo license0ESP32
QCamPCR
GaudiLabs
82.5 × 140 mm95 parts2LGPL-3.021
How designs wire the TLC59108xPW
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the TLC59108xPW connects to, and the resistors, capacitors and other passives placed on it.
- The REXT pin has a resistor to GND on 6 of 6 designs, most often 10 kΩ (then 4.7 kΩ).
- The A2 pin is tied to GND on 6 of 6 designs.
- The A3 pin is tied to GND on 6 of 6 designs.
- The SCL pin has a pull-up to 3.3V on 5 of 6 designs, most often 4.7 kΩ (then 10 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| REXTpin 1 | Connected to: Signal 100% |
|
| A0pin 2 | Connected to: GND 67% · VCC 33% | — |
| A1pin 3 | Connected to: GND 83% · 5V 17% | — |
| A2pin 4 | Connected to: GND 100% | — |
| A3pin 5 | Connected to: GND 100% | — |
| GNDpin 8, 13, 16 | Connected to: GND 100% | — |
| RESETpin 17 | Connected to: A connector 33% · 5V 33% |
|
| SCLpin 18 | Connected to: A connector 50%, the microcontroller 50%, 24AA02-OT 33% |
|
| SDApin 19 | Connected to: A connector 50%, the microcontroller 50%, 24AA02-OT 33% |
|
| VCCpin 20 | Connected to: 3.3V 100% |
|
8 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Isoblue by oats-center, QCamPCR by GaudiLabs, PingBoard by PingTechGmbH and IOT F26 PROJ by kaballian.
The TLC59108xPW in open source designs
The gallery holds 7 open source boards using the TLC59108xPW from 6 GitHub repositories; a typical one measures about 82.5 × 37.6 mm and carries around 68 components.
57% use four copper layers or more, and 57% carry an open source license.
The most starred is Isoblue by oats-center.
Parts used alongside the TLC59108xPW
What boards using the TLC59108xPW are built for
TLC59108xPW: common questions
Where can I find a TLC59108xPW reference design?
Each of the 7 boards on this page is a real design using the TLC59108xPW. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the TLC59108xPW REXT pin?
The REXT pin has a resistor to GND on 6 of 6 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 6 open source designs using the TLC59108xPW.
How is the TLC59108xPW A2 pin connected?
The A2 pin is tied to GND on 6 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the TLC59108xPW.
How is the TLC59108xPW A3 pin connected?
The A3 pin is tied to GND on 6 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the TLC59108xPW.
What parts are used alongside the TLC59108xPW?
The 24AA02-OT, MCP1700-3302E_SOT23, PESD2CAN, SN65HVD230 and STM32L432KCUx appear in the most repositories here.
Which microcontrollers do boards using the TLC59108xPW use?
Most are built on STM32 (3), ESP32 (2) and PIC (1).
How big is a typical board using the TLC59108xPW?
The median is 82.5 × 37.6 mm, and 43% are two-layer designs.
What is the most popular open source board using the TLC59108xPW?
By GitHub stars, Isoblue by oats-center, with 25 stars.
Can I simulate one of these boards using the TLC59108xPW before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.