10 open source boards using the TLV9062xD

Real designs built with the TLV9062xD, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

10 boardsClear filters|Most starred

How designs wire the TLV9062xD

Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the TLV9062xD connects to, and the resistors, capacitors and other passives placed on it.

  • Pin 1 has a series resistor on 8 of 8 designs, most often 47 Ω (then 100 kΩ).
  • The - pins have a series resistor on 8 of 8 designs, most often 470 Ω (then 100 Ω).
  • The + pins have a capacitor to GND on 7 of 8 designs, most often 33 nF (then 100 nF).
  • The V- pin is tied to GND on 8 of 8 designs.
Pin 1Connected to: Signal 100%
  • Series resistor on 100% · 47 Ω (3), 100 kΩ (1), 107 kΩ (1)
  • Series capacitor on 50% · 4.7 nF (3), 100 pF (1)
-pin 2, 6Connected to: Signal 94%
  • Series resistor on 100% · 470 Ω (6), 100 Ω (6), 10 kΩ (2)
  • Series capacitor on 63% · 4.7 nF (6), 100 pF (2)
+pin 3, 5Connected to: SN74CBT3253 38%
  • Capacitor to GND on 88% · 33 nF (6), 100 nF (3), 1 µF (1)
  • Series resistor on 50% · 100 kΩ (5), 300 Ω (2)
  • Resistor to GND on 38% · 3.53 kΩ (2), 150 kΩ (2), 8.2 kΩ (1)
V-pin 4Connected to: GND 100%
Pin 7Connected to: Signal 88%
  • Series resistor on 63% · 47 Ω (3), 220 Ω (1), 150 Ω (1)
  • Series capacitor on 50% · 4.7 nF (3), 100 pF (1)
V+pin 8Connected to: 5V 100%
  • Decoupling capacitor on 50% · 100 nF (4), 10 µF (1)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Batterymeter by hb020, Nexrig by alanmimms, Spartacus PCB REV1 by spartacus-hf and Chireix pcb by vpcsln.

The TLV9062xD in open source designs

The gallery holds 10 open source boards using the TLV9062xD from 10 GitHub repositories; a typical one measures about 100 × 93 mm and carries around 244 components.

100% use four copper layers or more, and 10% carry an open source license.

The most starred is Batterymeter by hb020.

Microcontrollers on boards using the TLV9062xD

TLV9062xD: common questions

Where can I find a TLV9062xD reference design?

Each of the 10 boards on this page is a real design using the TLV9062xD. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What resistor goes on the TLV9062xD pin 1?

Pin 1 has a series resistor on 8 of 8 designs, most often 47 Ω (then 100 kΩ). Counted from the KiCad layouts of 8 open source designs using the TLV9062xD.

What resistor goes on the TLV9062xD - pin?

The - pins have a series resistor on 8 of 8 designs, most often 470 Ω (then 100 Ω). Counted from the KiCad layouts of 8 open source designs using the TLV9062xD.

How is the TLV9062xD + pin connected?

The + pins have a capacitor to GND on 7 of 8 designs, most often 33 nF (then 100 nF). Counted from the KiCad layouts of 8 open source designs using the TLV9062xD.

What parts are used alongside the TLV9062xD?

The 161N-4BVS11, DSC1003DL2-008.0000T, LM1084IT-5.0G, MC74ACT541DTR2G and NE5532 appear in the most repositories here.

Which microcontrollers do boards using the TLV9062xD use?

Most are built on STM32 (7), AVR/Arduino (1) and NXP (1).

How big is a typical board using the TLV9062xD?

The median is 100 × 93 mm, and 0% are two-layer designs.

What is the most popular open source board using the TLV9062xD?

By GitHub stars, Batterymeter by hb020, with 20 stars.

Can I simulate one of these boards using the TLV9062xD before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part