11 open source boards using the TPS56339DDC
Real designs built with the TPS56339DDC, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Plantomation
Synthron
100 × 100 mm193 parts4LNo license10AVR/Arduino
Polaris4.1
porbital
95 × 99 mm90 parts2LNo license2STM32
Robotont electronics mainboard
robotont
304.3 × 274 mm407 parts2LNo license1ESP32
ELISTARS
R-Mutura
102 × 86.3 mm281 parts4LNo license0ESP32
Lilygo
Ndambia
77.9 × 81.6 mm147 parts4LNo license0ESP32
Hotplate
Keyaan-07
60 × 45 mm74 parts4LMIT0ESP32
Esp32stepper
szf2020
40 × 40 mm67 parts4LCERN-OHL-W-2.00PIC
Lightlink remote outlet
spstack
47 × 66 mm59 parts2LNo license0ESP32
Custom-ESP32
shyver
30 × 60 mm56 parts2LMIT0Raspberry Pi
Soraben
danielkent-net
85 × 38 mm36 parts2LCERN-OHL-S-2.00AVR/Arduino
Polaris3.1
porbital
95 × 99 mm69 parts2LNo license2
How designs wire the TPS56339DDC
Read from the KiCad layouts of 10 open source designs, one per repository: what each pin of the TPS56339DDC connects to, and the resistors, capacitors and other passives placed on it.
- The SW pin has a inductor on 10 of 10 designs, most often 4.7 µH (then 5.6 µH).
- The SW pin has a series capacitor on 10 of 10 designs, most often 100 nF.
- The VIN pin has a decoupling capacitor on 10 of 10 designs, most often 10 µF (then 100 nF).
- The BOOT pin has a series resistor on 10 of 10 designs, most often 30 Ω.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1 | Connected to: GND 100% | — |
| SWpin 2 | Connected to: Signal 90% |
|
| VINpin 3 | Connected to: 12V 90% |
|
| FBpin 4 | Connected to: Signal 90% |
|
| BOOTpin 6 | Connected to: Signal 100% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Plantomation by Synthron, Polaris3.1 by porbital, Robotont electronics mainboard by robotont and Soraben by danielkent-net.
The TPS56339DDC in open source designs
The gallery holds 11 open source boards using the TPS56339DDC from 10 GitHub repositories; a typical one measures about 85 × 81.6 mm and carries around 74 components.
55% are two-layer designs, the rest use four layers or more, and 36% carry an open source license.
The most starred is Plantomation by Synthron.
Parts used alongside the TPS56339DDC
Microcontrollers on boards using the TPS56339DDC
What boards using the TPS56339DDC are built for
TPS56339DDC: common questions
Where can I find a TPS56339DDC reference design?
Each of the 11 boards on this page is a real design using the TPS56339DDC. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the TPS56339DDC SW pin connected?
The SW pin has a inductor on 10 of 10 designs, most often 4.7 µH (then 5.6 µH). Counted from the KiCad layouts of 10 open source designs using the TPS56339DDC.
What decoupling capacitors do designs use on the TPS56339DDC VIN pin?
The VIN pin has a decoupling capacitor on 10 of 10 designs, most often 10 µF (then 100 nF). Counted from the KiCad layouts of 10 open source designs using the TPS56339DDC.
What resistor goes on the TPS56339DDC BOOT pin?
The BOOT pin has a series resistor on 10 of 10 designs, most often 30 Ω. Counted from the KiCad layouts of 10 open source designs using the TPS56339DDC.
Which microcontrollers do boards using the TPS56339DDC use?
Most are built on ESP32 (6), AVR/Arduino (2), PIC (1) and Raspberry Pi (1).
How big is a typical board using the TPS56339DDC?
The median is 85 × 81.6 mm, and 55% are two-layer designs.
What is the most popular open source board using the TPS56339DDC?
By GitHub stars, Plantomation by Synthron, with 10 stars.
Can I simulate one of these boards using the TPS56339DDC before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.