14 open source boards using the TPS61023DRLT
Real designs built with the TPS61023DRLT, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
FPGA
Thunderscope Rev5.3
EEVengers
122.5 × 103.5 mm817 parts6LMIT1.3kESP32
OpenAirScope
emertcakir
100 × 75 mm247 parts4LMIT26FPGA
SIG COND
Han-ZenX
122.5 × 103.5 mm817 parts6LCustom license1ESP32
PCB V3.1
Jonathan-0101
80 × 160 mm287 parts4LGPL-3.01ESP32
IOT-project
datnguyenhcmut
100 × 75 mm247 parts4LMIT0ESP32
Keypad board
TheZlodziej
160 × 124 mm121 parts2LNo license0Battery-Management
SingularTeabag
32.3 × 11.5 mm34 parts2LGPL-3.00Buoy
wbarne12
30 × 60 mm30 parts2LNo license0ESP32
PCB V2.2 PreAutoRoute
Jonathan-0101
80 × 161 mm286 parts4LGPL-3.01ESP32
Main
Ajakovski
100 × 120 mm30 parts4LMIT1Nrf watch
yuxiangcheng2002
36 × 36 mm71 parts4LNo license0ESP32
PCB V2.2 PreAutoRoute DimChange
Jonathan-0101
80 × 161 mm286 parts4LGPL-3.01ESP32
PCB V2.4 Backup
Jonathan-0101
80 × 161 mm286 parts4LGPL-3.01ZSWatch
yuxiangcheng2002
40.9 × 38 mm62 parts4LNo license0
How designs wire the TPS61023DRLT
Read from the KiCad layouts of 10 open source designs, one per repository: what each pin of the TPS61023DRLT connects to, and the resistors, capacitors and other passives placed on it.
- The FB pin has a resistor to GND on 10 of 10 designs, most often 100 kΩ (then 35.7 kΩ).
- The VIN pin has a inductor on 9 of 10 designs, most often 1 µH.
- The SW pin has a inductor on 9 of 10 designs, most often 1 µH.
- The VOUT pin has a decoupling capacitor on 9 of 10 designs, most often 22 µF (then 1 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| FBpin 1 | Connected to: Signal 100% |
|
| ENpin 2 | Connected to: MCP73871-2CAI/ML 20% · VBUS 20% |
|
| VINpin 3 | Connected to: MCP73871-2CAI/ML 20% · VUSB_R 40% |
|
| GNDpin 4 | Connected to: GND 100% | — |
| SWpin 5 | Connected to: Signal 100% |
|
| VOUTpin 6 | Connected to: 5V 70% · a signal 30% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Thunderscope Rev5.3 by EEVengers, OpenAirScope by emertcakir, Main by Ajakovski and SIG COND by Han-ZenX.
The TPS61023DRLT in open source designs
The gallery holds 14 open source boards using the TPS61023DRLT from 10 GitHub repositories; a typical one measures about 80 × 103.5 mm and carries around 247 components.
79% use four copper layers or more, and 64% carry an open source license.
The most starred is Thunderscope Rev5.3 by EEVengers.
Parts used alongside the TPS61023DRLT
What boards using the TPS61023DRLT are built for
TPS61023DRLT: common questions
Where can I find a TPS61023DRLT reference design?
Each of the 14 boards on this page is a real design using the TPS61023DRLT. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the TPS61023DRLT FB pin?
The FB pin has a resistor to GND on 10 of 10 designs, most often 100 kΩ (then 35.7 kΩ). Counted from the KiCad layouts of 10 open source designs using the TPS61023DRLT.
How is the TPS61023DRLT VIN pin connected?
The VIN pin has a inductor on 9 of 10 designs, most often 1 µH. Counted from the KiCad layouts of 10 open source designs using the TPS61023DRLT.
How is the TPS61023DRLT SW pin connected?
The SW pin has a inductor on 9 of 10 designs, most often 1 µH. Counted from the KiCad layouts of 10 open source designs using the TPS61023DRLT.
What parts are used alongside the TPS61023DRLT?
The ADA4930-1YCPZ-R7, BQ25185DLHR, BUF802IRGTR, DS3231M+TRL and EMIF06-MSD02N16 appear in the most repositories here.
Which microcontrollers do boards using the TPS61023DRLT use?
Most are built on ESP32 (8) and FPGA (2).
How big is a typical board using the TPS61023DRLT?
The median is 80 × 103.5 mm, and 21% are two-layer designs.
What is the most popular open source board using the TPS61023DRLT?
By GitHub stars, Thunderscope Rev5.3 by EEVengers, with 1,336 stars.
Can I simulate one of these boards using the TPS61023DRLT before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.