20 open source boards using the LP5907MFX-3.3/NOPB
Real designs built with the LP5907MFX-3.3/NOPB, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
FPGAFomu hardware
im-tomu
90 × 50 mm57 parts2LCC-BY-SA-4.0235
OpenPCIE
chili-chips-ba
179.1 × 92.3 mm170 parts4LBSD-3-Clause102
HPM5E31 ECatDualFOC
LX050724
85 × 113 mm559 parts4LMIT14
STM32Dib mio168
eez-open
146 × 95 mm237 parts4LTAPR-OHL-1.09
ESP32Doorbell controller
gunnarbeutner
64 × 59 mm102 parts4LMIT1
ESP32Exhaust mic
HasiKe
72 × 55 mm133 parts4LNo license0
ESP32Waypoint
M-Mrk
140 × 80 mm129 parts4LNo license0
Merged17
pentolope
120 × 120 mm103 parts4LNo license0
Microphone array v2
120 × 120 mm103 parts4LNo license0
IM72D128-Tube
hbitter
130 × 11 mm21 parts2LGPL-3.088
Microphone array v2
120 × 120 mm103 parts4LNo license0
Reroute signals only
120 × 120 mm103 parts4LNo license0
Reroute via clean
120 × 120 mm103 parts4LNo license0
Reroute signals only
120 × 120 mm103 parts4LNo license0
ESP32Eps-8pin rev3
nathanfraske
96 × 40 mm63 parts4LApache-2.00
Reroute via clean
120 × 120 mm103 parts4LNo license0
Routed17
120 × 120 mm103 parts4LNo license0
ESP32CEC PCIe 8-pin 3-Port Module
103.4 × 56 mm54 parts4LApache-2.00
ESP3224pin module
82.9 × 79 mm46 parts4LApache-2.00
ESP32CEC PCIe 8-pin 2-Port Module
86.4 × 44 mm45 parts4LApache-2.00
The LP5907MFX-3.3/NOPB in open source designs
The gallery holds 20 open source boards using the LP5907MFX-3.3/NOPB from 11 GitHub repositories; a typical one measures about 120 × 93.7 mm and carries around 103 components.
90% use four copper layers or more, and 50% carry an open source license.
The most starred is Fomu hardware by im-tomu.
Parts used alongside the LP5907MFX-3.3/NOPB
What boards using the LP5907MFX-3.3/NOPB are built for
LP5907MFX-3.3/NOPB: common questions
Where can I find a LP5907MFX-3.3/NOPB reference design?
Each of the 20 boards on this page is a real design using the LP5907MFX-3.3/NOPB. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
Which microcontrollers do boards using the LP5907MFX-3.3/NOPB use?
Most are built on ESP32 (7), FPGA (1) and STM32 (1).
How big is a typical board using the LP5907MFX-3.3/NOPB?
The median is 120 × 93.7 mm, and 10% are two-layer designs.
What is the most popular open source board using the LP5907MFX-3.3/NOPB?
By GitHub stars, Fomu hardware by im-tomu, with 235 stars.
Can I simulate one of these boards using the LP5907MFX-3.3/NOPB before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.