14 open source boards using the 555

Real designs built with the 555, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

14 boardsClear filters|Most starred

How designs wire the 555

Read from the KiCad layouts of 13 open source designs, one per repository: what each pin of the 555 connects to, and the resistors, capacitors and other passives placed on it.

  • The THRES pin has a capacitor to GND on 11 of 13 designs, most often 1 µF (then 4.7 µF).
  • The CONT pin has a capacitor to GND on 10 of 13 designs, most often 10 nF (then 100 nF).
  • The TRIG pin has a series resistor on 9 of 13 designs, most often 10 kΩ (then 100 Ω).
  • The DISCH pin has a pull-up to 5V on 9 of 13 designs, most often 1 MΩ (then 1 kΩ).
GNDpin 1Connected to: GND 92%
TRIGpin 2Connected to: Signal 100%
  • Series resistor on 69% · 10 kΩ (3), 100 Ω (2), 47 kΩ (1)
  • Capacitor to GND on 46% · 1 µF (2), 100 nF (1), 4.7 µF (1)
  • Pull-up to 5V on 38% · 1 kΩ (2), 1 MΩ (1), 100 kΩ (1)
OUTpin 3Connected to: Signal 100%
  • Series resistor on 54% · 10 kΩ (4), 470 Ω (2), 2 kΩ (2)
RSTpin 4Connected to: 5V 77% · a signal 23%
CONTpin 5Connected to: Signal 92%
  • Capacitor to GND on 77% · 10 nF (5), 100 nF (4)
THRESpin 6Connected to: Signal 100%
  • Capacitor to GND on 85% · 1 µF (3), 4.7 µF (2), 10 µF (2)
  • Pull-up to 5V on 62% · 1 MΩ (2), 100 kΩ (2), 10 kΩ (2)
  • Series resistor on 54% · 100 Ω (2), 10 kΩ (2), 100 kΩ (2)
DISCHpin 7Connected to: Signal 77% · not connected 23%
  • Pull-up to 5V on 69% · 1 MΩ (2), 1 kΩ (2), 100 kΩ (2)
  • Capacitor to GND on 46% · 10 µF (2), 470 nF (1), 1 µF (1)
  • Series resistor on 31% · 100 kΩ (2), 1 kΩ (1), 10 kΩ (1)
VCCpin 8Connected to: 5V 85% · a signal 15%
  • Decoupling capacitor on 46% · 100 nF (6), 10 µF (1)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include 68000 by jefftranter, Poly555 by oskitone, Universal-ITX-Backplane by spark2k06 and Clock by DutchMaker.

The 555 in open source designs

The gallery holds 14 open source boards using the 555 from 13 GitHub repositories; a typical one measures about 99.8 × 99.8 mm and carries around 65 components.

79% are two-layer designs, the rest use four layers or more, and 29% carry an open source license.

The most starred is 68000 by jefftranter.

Parts used alongside the 555

Microcontrollers on boards using the 555

555: common questions

Where can I find a 555 reference design?

Each of the 14 boards on this page is a real design using the 555. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the 555 THRES pin connected?

The THRES pin has a capacitor to GND on 11 of 13 designs, most often 1 µF (then 4.7 µF). Counted from the KiCad layouts of 13 open source designs using the 555.

How is the 555 CONT pin connected?

The CONT pin has a capacitor to GND on 10 of 13 designs, most often 10 nF (then 100 nF). Counted from the KiCad layouts of 13 open source designs using the 555.

What resistor goes on the 555 TRIG pin?

The TRIG pin has a series resistor on 9 of 13 designs, most often 10 kΩ (then 100 Ω). Counted from the KiCad layouts of 13 open source designs using the 555.

Which microcontrollers do boards using the 555 use?

Most are built on STM32 (3) and ESP32 (1).

How big is a typical board using the 555?

The median is 99.8 × 99.8 mm, and 79% are two-layer designs.

What is the most popular open source board using the 555?

By GitHub stars, 68000 by jefftranter, with 132 stars.

Can I simulate one of these boards using the 555 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part