101 open source boards using the 4017
Real designs built with the 4017, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Klangorium
hexagon5un
200 × 100 mm152 parts2LNo license65AVR/Arduino
Peripheral board
trollectronics
165 × 100 mm248 parts2LNo license22ESP8266
Rick-Flash
rectifiedtech
80 × 24 mm19 parts2LMIT21Sequencer
sphawes
70.8 × 108.5 mm38 parts2LNo license14E dice
polaracep
105.5 × 34.5 mm48 parts2LAGPL-3.08- schematic only · 48 parts
Bent wavefield
wenbakefield
48 partsNo license6 Sequencer
elandahl
61.9 × 108.7 mm65 parts2LNo license5Nibble plusplus
Binary-Kitchen
40 × 40 mm19 parts2LCC-BY-SA-4.05OBeMS
johnbeardmore
180 × 120 mm123 parts2LLGPL-3.03UniBadge-9x9
marove2000
50 × 50 mm108 parts2LCC-BY-SA-4.03BabyOdes
oficinadesonido
60.1 × 109.8 mm91 parts2LGPL-3.03Ruler V2
ben5049
155 × 30 mm17 parts2LApache-2.03Nintendo Famicom Keyboard HVC-007
BrettHallen
380 × 160 mm100 parts2LNo license2SchrittMacher
c-base
99.7 × 71.5 mm90 parts2LNo license2Led chaser
notyourcto
87 × 38.9 mm30 parts2LNo license2- schematic only · 64 parts
Squarely
Broosky
64 partsNo license2 STM32
Smdboard
adamgreig
50 × 50 mm164 parts2LNo license1AVR/Arduino
Main
qweqq
158.8 × 65.7 mm116 parts2LMIT1Power tx
redhotchili0909
124 × 119.9 mm91 parts2LNo license1Christmas Light
Az154za
73.3 × 37 mm32 parts2LNo license1555-chaser led flower
anya39
93.2 × 93.9 mm19 parts2LNo license1555-LED-Chaser
VritoX098
37.9 × 21.5 mm19 parts2LNo license1JL-rev1
acastles91
500 × 272.5 mm298 parts4LNo license0GikFun-LED-Chaser-RE
SmoothBraneIndustries
89 × 105 mm138 parts2LNo license0ExED
lucaci32u4
117.2 × 115.1 mm135 parts2LGPL-3.00SEQUENCER
theWickedWebDev
223.8 × 105.7 mm102 parts2LNo license0Digital clock
guilhermegch
100 × 100 mm96 parts2LNo license0Gsa d1
tjb803
100 × 100 mm94 parts2LMIT0555-Chaser-LED
code-ga
99.2 × 94.3 mm74 parts4LNo license0CDJC
rick0x00
91.3 × 100 mm55 parts2LApache-2.00SMD Lauflicht
Binary-Kitchen
40 × 40 mm54 parts2LCC0-1.00COUNTER V01
jmos1
160 × 68.6 mm53 parts2LNo license0FabLab-SMD-Soldering
FabLab-Freising
81.1 × 46.2 mm48 parts2LCERN-OHL-S-2.00Password
SeanCarr1
48.3 × 31.6 mm30 parts2LNo license0LED-Chaser-555-4017
DIVAKAR-516-RAGHU
59 × 86.5 mm29 parts2LNo license0LED-chaser
jenna2004jna
39.8 × 81.5 mm28 parts2LNo license0
How designs wire the 4017
Read from the KiCad layouts of 87 open source designs, one per repository: what each pin of the 4017 connects to, and the resistors, capacitors and other passives placed on it.
- The COUT pin is left unconnected on 83 of 87 designs (a signal on 4).
- The CKEN pin is tied to GND on 71 of 87 designs (not connected on 2, a signal on 14).
- The RESET pin is tied to GND on 53 of 87 designs (not connected on 10, a signal on 24).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VSSpin 8 | Connected to: GND 92% | — |
| COUTpin 12 | Connected to: Not connected 95% | — |
| CKENpin 13 | Connected to: GND 82% · a signal 16% | — |
| RESETpin 15 | Connected to: GND 61% · a signal 28% | — |
| VDDpin 16 | Connected to: 5V 85% | — |
11 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Klangorium by hexagon5un, RS64c PS by lhm0, Peripheral board by trollectronics and Rick-Flash by rectifiedtech.
The 4017 in open source designs
The gallery holds 101 open source boards using the 4017 from 91 GitHub repositories; a typical one measures about 89.5 × 73.4 mm and carries around 22 components.
93% are two-layer designs, the rest use four layers or more, and 34% carry an open source license.
The most starred is Klangorium by hexagon5un.
Parts used alongside the 4017
Microcontrollers on boards using the 4017
What boards using the 4017 are built for
4017: common questions
Where can I find a 4017 reference design?
Each of the 101 boards on this page is a real design using the 4017. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the 4017 COUT pin connected?
The COUT pin is left unconnected on 83 of 87 designs (a signal on 4). Counted from the KiCad layouts of 87 open source designs using the 4017.
How is the 4017 CKEN pin connected?
The CKEN pin is tied to GND on 71 of 87 designs (not connected on 2, a signal on 14). Counted from the KiCad layouts of 87 open source designs using the 4017.
How is the 4017 RESET pin connected?
The RESET pin is tied to GND on 53 of 87 designs (not connected on 10, a signal on 24). Counted from the KiCad layouts of 87 open source designs using the 4017.
What parts are used alongside the 4017?
The NE555P, NE555, 74LS08, NE555D and 4051 appear in the most repositories here.
Which microcontrollers do boards using the 4017 use?
Most are built on RP2040/RP2350 (3), AVR/Arduino (3), ESP8266 (1) and STM32 (1).
How big is a typical board using the 4017?
The median is 89.5 × 73.4 mm, and 93% are two-layer designs.
What is the most popular open source board using the 4017?
By GitHub stars, Klangorium by hexagon5un, with 65 stars.
Can I simulate one of these boards using the 4017 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.